20.0 hp electric start 42" mower automatic lawn tractor (52 pages)
Summary of Contents for Sears Craftsman CTX 9000
Page 1
107.250040 (20 Gross HP Briggs & Stratton with 42” Mower) For answers to your questions about this product, call Sears Craftsman Help Line 1-800-659-5917. Sears Brands Management Corporation, Hoff man Estates, IL 60179 U.S.A. Visit our Craftsman website: www.craftsman.com 1753798 Revision A...
TABLE OF CONTENTS Front Cover .........................1 Operator Safety ......................4 Features and Controls .....................10 Operation ........................13 Safety Interlock System Tests .................13 Maintenance ......................18 Troubleshooting .......................28 Specifi cations ......................30 Warranty ........................31 Repair Protection Agreement..................32 Service Parts .......................PTS-1 Thank you for purchasing this quality-built CRAFTSMAN mower. We're pleased that you've placed your confidence in the CRAFTSMAN brand.
OPERATOR SAFETY Operating Safety Congratulations on purchasing a superior-quality piece of lawn and garden equipment. Our products are designed and manufactured to meet or exceed all industry standards for safety. Power equipment is only as safe as the operator. If it is misused, or not properly maintained, it can be dangerous! Remember, you are responsible for your safety and that of those around you.
Page 5
Slope Operation You could be seriously injured or even killed if you use this unit on too steep an incline. Using the unit on a slope that is too steep or where you don’t have adequate traction can cause you to lose control or roll over. A good rule of thumb is to not operate on any slope you cannot back up (in 2-wheel drive mode).
Page 6
Read these safety rules and follow them closely. Failure to obey these rules could result in loss of control of unit, severe personal injury or death to you, or bystanders, or damage to property or equipment. This mowing deck is capable of amputating hands and feet and throwing objects. The triangle in text signifies important cautions or warnings which must be followed.
Page 7
SLOPE OPERATION WARNING Slopes are a major factor related to loss-of-control and tip-over Never operate on slopes greater than 17.6 percent accidents, which can result in severe injury or death. Operation (10°) which is a rise of 3-1/2 feet (106 cm) vertically in on all slopes requires extra caution.
Page 8
SERVICE AND MAINTENANCE Safe Handling of Gasoline 1. Extinguish all cigarettes, cigars, pipes, and other 12. Do not use gasoline containing METHANOL, gasohol sources of ignition. containing more than 10% ETHANOL, gasoline 2. Use only approved gasoline containers. additives, or white gas because engine/fuel system 3.
Page 9
Decal Locations (Safety and Operation) Decal - Operating Instructions, Part No. 1734879 Decal - Ignition Switch Positions Part No. 1722806 Danger, Side Discharge Models, Part No. 1704277 Danger, Side Discharge Models, Part No. 1704277 173xxxx Transmission Release Part No. 1730202 Figure 1...
FEATURES AND CONTROLS Figure 2 Control Functions Reverse Mowing Option (RMO) Throttle Control The Reverse Mowing Option allows for mowing (or use of other PTO driven attachments) while traveling in reverse. The throttle controls engine speed (see Figure 2). Move If you choose to mow or operate another attachment in the throttle forward to increase engine speed and back to reverse, turn the RMO key after the PTO is engaged.
Page 11
PTO Switch Mower Height of Cut Adjustment The cutting height is adjustable between 1.5” and 4.0” The PTO (Power Take-Off) switch engages and (3,8 and 10,2 cm). disengages attachments that use the PTO. To engage the PTO, pull UP on the switch. Push DOWN to disengage. The cutting height adjustment switch controls the mower Note that the operator must be seated firmly in the tractor cutting height.
Page 12
Hourmeter The hourmeter (Figure 3) measures the number of hours the key has been in the RUN position. The hourmeter will fl ash an initial oil change indicator at 5 hours, and a lubrication reminder every 50 hours. These reminders display for approximately two hours and will automatically HOURS 1/10...
Before adding or checking the oil switch is turned OFF. If mower drive belt does not stop • Place engine level. within five seconds, contact Sears Service. • Clean the oil fill area of any debris. Test 5 — Reverse Mow Option (RMO) Check 1.
Page 14
High Altitude At altitudes over 5,000 feet (1,524 meters), a minimum 85 octane/85 AKI (89 RON) gasoline is acceptable. To remain emissions compliant, high altitude adjustment is required. Operation without this adjustment will cause decreased performance, increased fuel consumption, and increased emissions. See an authorized dealer for high altitude adjustment information.
Page 15
1. Clean the fuel cap area of dirt and debris. Remove 1. Check the oil level. See the How to Check/Add Oil the fuel cap (A, Figure 6). section. 2. Make sure equipment drive controls are disengaged. 2. Fill the fuel tank with fuel. To allow for expansion of the gasoline, do not fill above the bottom of the 3.
Page 16
WARNING The engine will shut off if the reverse ground speed pedal is depressed while the PTO is on and the RMO has not been activated. The operator should always turn the PTO off prior to driving across on roads, paths or any area that maybe used by other vehicles.
Page 17
Attaching a Trailer Adjusting Mower Cutting Height The maximum horizontal drawbar force allowed 444 Newton. The cutting height is adjustable between 1.5” and 4.0” (3,8 The maximum vertical drawbar force is 222 Newton. This and 10,2 cm). equates to a 396 lbs (180 kg) trailer on a 10 degree hill. The cutting height adjustment switch (A, Figure 8) controls Secure the trailer with an appropriately sized clevis pin (A, the mower cutting height.
MAINTENANCE Maintenance Chart ENGINE TRACTOR AND MOWER Every 8 Hours or Daily First 5 Hours Check safety interlock system Change engine oil - see engine manual Clean debris off tractor and mower deck Every 8 Hours or Daily Clean debris from engine compartment Check engine oil level - see engine manual Every 25 Hours or Annually * Every 25 Hours or Annually *...
Page 19
If starting or operation problems disconnect the negative cable FIRST and reconnect occur, contact Sears Service. it LAST. If not done in this order, the positive terminal can be shorted to the frame by a tool.
Page 20
Figure 13 Changing the Oil Standard Oil Drain Plug Used oil is a hazardous waste product and must be 1. Remove the oil drain plug (B, Figure 13). Drain the oil disposed of properly. Do not discard with household into an approved container. waste.
Page 21
Changing the Oil Filter Add Oil For replacement intervals, see the Maintenance Chart. • Place engine level. 1. Drain the oil from the engine. See Remove Oil sec- • Clean the oil fill area of any debris. tion. • See the Specifications section for oil capacity. 2.
Page 22
Figure 16 Figure 15 Removing the Mower Deck WARNING Engage the parking brake, disengage PTO, stop engine, and remove key before attempting to remove the mower deck. 1. Park the tractor on a hard, level surface such as a concrete floor. Turn off PTO switch and engine, remove the key, and apply the parking brake.
Page 23
4. Install cotter pin (A, Figure 17) and washer (B) that attach mower support (C) to tractor frame. Repeat for other side. 5. Pull the idler pulley lever (A, Figure 16) to release belt tension. Install belt (B) on the PTO pulley (C). Figure 18 Installing the Mower Deck WARNING...
Page 24
Lubricate Mower Deck PTO Belt Replacement Lubricate the mower deck at the locations shown in Figure WARNING To avoid damaging belts, do not pry belts over pulleys. 1. Park the tractor on a smooth, level surface such as a concrete driveway. Disengage the PTO, turn off the engine, and lock the parking brake.
Page 25
PTO Clutch Adjustment Check the PTO clutch adjustment after the initial 25 hour break-in period and then after every 250 hours of operation. Also perform the following procedure if the clutch is slipping or will not engage, or if a new clutch has been installed. 1.
Page 26
Servicing the Mower Blades WARNING For your personal safety, do not handle the sharp mower blades with bare hands. Careless or improper handling of blades may result in serious injury. WARNING For your personal safety, blade mounting capscrews must each be installed with a hex/spline washer and spring washer, then securely tightened.
Page 27
Storage Fuel System Fuel can become stale when stored over 30 days. Stale fuel causes acid and gum deposits to form in the fuel sys- WARNING tem or on essential carburetor parts. To keep fuel fresh, use fuel stabilizer. Never store the unit (with fuel) in an enclosed, poorly ventilated structure.
Troubleshooting the Tractor Troubleshooting the Tractor (Continued) PROBLEM LOOK FOR REMEDY Internal brake worn. Contact Sears Service. Brake will not hold. Steering linkage is loose. Contact Sears Service. Improper tire infl ation. See Check Tire Pressure section. Tractor steers hard or handles poorly.
Page 29
Move knob to NEUTRAL/OFF position. Out of fuel. If engine is hot, allow it to cool, then refi ll the fuel tank. Fuse is blown. Replace fuse or contact Sears Service. Battery terminals require See Cleaning the Battery and Cables section. cleaning.
Normal deterioration and wear of the exterior fi nishes, or product label replacement. This warranty gives you specifi c legal rights, and you may also have other rights which vary from state to state. Sears Brands Management Corporation, Hoff man Estates, IL 60179...
U.S.A. or Canada call 1-800-4-MY- Fast help by phone – we call it Rapid Resolution – HOME®. phone support from a Sears representative. Think of us as a “talking owner’s manual.”...
Page 36
Steering Group CTX9000 - 107.250040 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. PTS - 2...
Page 37
Steering Group CTX9000 - 107.250040 REF NO PART NO. QTY. DESCRIPTION 0010 1727813SM SHAFT, Steering Gear & Spline 0020 1960114SM WASHER, 3/4 x 1.06 OD 0030 1729665SM BUSHING, Steering, 3/4 ID 0030 1729665SM BUSHING, Steering, 3/4 ID 0040 7078088YP STEERING WHEEL, UV-2 0050 1960576SM NUT, Hex Lock, ESNA, 5/8-18...
Page 38
Decal Group CTX9000 - 107.250040 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. PTS - 4...
Page 39
0080 1730202SM DECAL, Transmission Tow / Release Lever 0090 1722806SM DECAL, Ignition, RZT 0100 1753784YP DECAL, 20HP Sears Service Parts 0180 1753769YP DECAL, Model CTX9000 Craftsman 0190 1734375SM DECAL, Die Hard (not shown in illustration, placed on battery) 1010 7101665YP...
Page 40
Electrical Group CTX9000 - 107.250040 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. PTS - 6...
Page 41
Electrical Group CTX9000 - 107.250040 REF NO PART NO. QTY. DESCRIPTION 0010 1753847YP HARNESS, Wiring 0010-10 1731957SM FUSE, Wiring Harness 0030 1930601SM SCREW, Hex Washer Head, Taptite, 5/16-18 x 5/8 0040 ----- BATTERY, 12V, 230CCA 0050 1730007SM HOLD DOWN, Battery 0060 1931318SM BOLT, Carriage, Short Neck, 1/4-20 x 7/8, G5...
Page 42
Electrical Group CTX9000 - 107.250040 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. PTS - 8...
Page 43
Electrical Group CTX9000 - 107.250040 REF NO PART NO. QTY. DESCRIPTION 0710 1753757BMYP BRACKET, Indicator Hold Down 0730 1722611SM PLUG, Hole 0740 7091696YP SCREW, Philips, Pan Head, Self Tapping 0750 1930641SM NUT, Hex Flange, Whiz Lock, 1/4-20 Footnotes PTS - 9...
Page 44
Lift Group - Electric CTX9000 - 107.250040 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. PTS - 10...
Page 45
Lift Group - Electric CTX9000 - 107.250040 REF NO PART NO. QTY. DESCRIPTION 0070 1931277SM NUT, Hex Flange, Whiz Lock, 5/16-18 0100 1731417AYP ARM, Rear Lift 0110 1732426SM BOLT, Shoulder, 5/16-18 x 9/16 0120 1727955SM ROD, Lift, Lower, 3/8 x 10 Long 0150 1731894SM TRUNNION...
Page 46
Controls Group CTX9000 - 107.250040 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. PTS - 12...
Page 54
Transmission Group CTX9000 - 107.250040 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. PTS - 20...
Page 55
Transmission Group CTX9000 - 107.250040 REF NO PART NO. QTY. DESCRIPTION 0010 1729589SM TRANSMISSION ASSEMBLY, Tuff Torque, K46BL 0030 1960586SM CAPSCREW, Hex, Whiz Lock, 5/16-18 x 2-1/2 0040 1931277SM NUT, Hex Flange, Whiz Lock, 5/16-18 0050 1728120SM ROD, Bypass, 1/4 Dia. x 11-7/16" Long 0060 1722460SM PIN, Quick, 1-3/16 Long...
Page 56
Hood, Grille & Dash Group CTX9000 - 107.250040 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. PTS - 22...
Page 57
Hood, Grille & Dash Group CTX9000 - 107.250040 REF NO PART NO. QTY. DESCRIPTION 0010 1722110ZYP HOOD, with Louvers 0020 7102326YP AIR DUCT, Plenum 0030 1728029ZYP PANEL, R.H. Side 0040 1728030ZYP PANEL, L.H. Side 0050 1727297BRYP GRILLE 0060 1727279AYP HINGE, Hood, L.H. 0070 1727280AYP HINGE, Hood, R.H.
Page 58
Seat Deck & Fuel Tank Group - EVAP Compliant CTX9000 - 107.250040 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. PTS - 24...
Page 59
Seat Deck & Fuel Tank Group - EVAP Compliant CTX9000 - 107.250040 REF NO PART NO. QTY. DESCRIPTION 0010 1727264ZYP DECK, Seat 0020 1931333SM BOLT, Carriage, 5/16-18 x 3/4, G5 0030 1931277SM NUT, Hex Flange, Whiz Lock, 5/16-18 0040 1728007SM PAD, Footrest R.H.
Page 60
Wheels & Tires Group CTX9000 - 107.250040 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. PTS - 26...
Page 61
Wheels & Tires Group CTX9000 - 107.250040 REF NO PART NO. QTY. DESCRIPTION 0010 2860202SM WASHER, 3/4 0020 1754160YP WHEEL & TIRE ASSEMBLY, Front, 15 x 6-6 (Includes Ref. Nos. 0020-10, 0020-20, 0020-30, 0020-40 & 0020-50) 0020-10 1733882SM TIRE, 15 x 6-6, Front 0020-20 1726301SM WHEEL &...
Page 62
Transmission SERVICE PARTS - Tuff Torq K46BL CTX9000 - 107.250040 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. PTS - 28...
Page 63
Transmission SERVICE PARTS - Tuff Torq K46BL CTX9000 - 107.250040 REF NO PART NO. QTY. DESCRIPTION 1729589SM * TRANSMISSION, Tuff Torq K46BL ----- KIT, Upper Case ----- LOWER CASE 1718052SM VENT VALVE 15 1724279SM MAGNET ----- * MAGNET HOLDER ----- * KIT, Pump Shaft/Bearing ----- * SPRING 25...
Page 64
Transmission SERVICE PARTS - Tuff Torq K46BL CTX9000 - 107.250040 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. PTS - 30...
Page 65
Transmission SERVICE PARTS - Tuff Torq K46BL CTX9000 - 107.250040 REF NO PART NO. QTY. DESCRIPTION ----- * CONTROL ARM A 1724347SM CONTROL LEVER C ----- * JERKY PLATE 1708689SM WASHER, 12 1724349SM COTTER PIN, 1/8 * 3/4 1724296SM SPRING PIN 6 * 36 1718100SM ROLL PIN 6 * 40 1707879SM...
Page 66
42" Mower Deck - Support Group CTX9000 - 107.250040 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. PTS - 32...
Page 67
42" Mower Deck - Support Group CTX9000 - 107.250040 REF NO PART NO. QTY. DESCRIPTION 0010 1731966BMYP HITCH, Front 0020 1730097SM ROD, Bail 0030 1730221ASM HANGER, Front 0040 1679166SM SPACER, 1/2 ID x 7/8 OD x 1-3/16" 0050 1960379SM NUT, Hex Lock, ESNA LIGHT, 1/2-13 0060 2176012SM RETAINER, Pin Spring...
Page 68
42" Mower Deck - Clutch Group CTX9000 - 107.250040 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. PTS - 34...
Page 69
42" Mower Deck - Clutch Group CTX9000 - 107.250040 REF NO PART NO. QTY. DESCRIPTION 0010 1922130SM CAPSCREW, Hex Head, 3/8-16 x 2-1/4, G5 0020 1922755SM WASHER, 3/8 x 1 OD 0030 7018574SM IDLER, Flat, 4-1/8 0040 1960339SM NUT, Hex Flange, 3/8-16, Locking 0050 1924356SM WASHER, 3/8 x 1-1/2 OD...
Page 70
42" Mower Deck - Housing, Arbors & Blades CTX9000 - 107.250040 NOTE: Unless noted otherwise, use the standard hardware torque specification chart. PTS - 36...
Page 87
107.250040 (20HP brutos Briggs & Stratton con cortacésped de 42 pulg.) Para obtener respuestas a sus preguntas sobre este producto, llame al: Línea de ayuda de Sears Craftsman 1-800-659-5917. Sears Brands Management Corporation, Hoff man Estates, IL 60179 EE. UU Visite nuestro sitio Web de Craftsman: www.craftsman.com...
Page 89
TABLA DE CONTENIDO Tapa delantera ......................1 Seguridad del operador .....................4 Características y controles ..................10 Funcionamiento ......................13 Pruebas del sistema de interbloqueo de seguridad ..........13 Mantenimiento ......................18 Solución de problemas ....................28 Especifi caciones ......................30 Garantía ........................31 Acuerdos de protección para reparaciones ............32 Repuestos ......................PTS-1...
SEGURIDAD DEL OPERADOR Manejar el equipo con seguridad Felicidades por haber adquirido un equipo de jardín y campo de alta calidad. Nuestros productos están diseñados y fabricados para cumplir o exceder todas las normas de seguridad del sector. El equipo electrónico solamente es seguro dependiendo de cómo lo utilice el operador.
Page 91
Funcionamiento en cuestas Podría lesionarse gravemente o incluso matarse si utiliza esta unidad en cuestas demasiado pronunciadas. El uso de la unidad en una pendiente que sea demasiado pronunciada o donde no posea la tracción adecuada puede hacer que pierda el control o que vuelque. Un buen consejo es no utilizar la máquina en ninguna pendiente sobre la que no pueda ir marcha atrás (en modo tracción a dos ruedas).
Page 92
Lea estas normas de seguridad y respételas estrictamente. El no respetar estas normas podría dar como resultado la pérdida del control de la unidad, lesiones personales graves o la muerte del usuario o de terceros que se encuentren cerca, o podría causar daños en la propiedad o en el equipo. La cubierta del cortacésped puede llegar a amputar manos y pies y lanzar objetos.
Page 93
FUNCIONAMIENTO EN PENDIENTES ADVERTENCIA Las pendientes son un factor de gran pérdida en los casos de pérdida de control y en los accidentes en los que vuelca el cortacésped, que pueden Nunca opere en pendientes de más del 17,6% (10°); esos resultar en lesiones graves o incluso la muerte.
Page 94
REPARACIÓN Y MANTENIMIENTO 12. No utilice gasolina que METANOL, gasohol que contenga más del 10% de ETANOL, aditivos para la gasolina, o white gas; el Säker hantering av bensin motor o el sistema de alimentación podrían resultar dañados. 1. Apague todos los cigarrillos, puros, pipas y cualquier otra fuente 13.
Page 95
Ubicaciones de las calcomanías (Seguridad y funcionamiento) Calcomanía - Instrucciones de funcionamiento N° de pieza 1734879 Calcomanía - Posiciones del interruptor de ignición N° de pieza 1722806 Peligro, modelos con descarga lateral N° de pieza 7101665 Peligro, modelos con descarga lateral N°...
CARACTERÍSTICAS Y CONTROLES Figura 2 Funciones de control Opción de corte marcha atrás (RMO, Control de la mariposa por sus siglas en inglés) La mariposa controla la velocidad del motor (consulte Figura La Opción de Cortar el Césped Marcha Atrás (RMO) permite 2).
Page 97
Ajuste de la altura de corte del Interruptor PTO cortacésped La altura de corte puede ajustarse entre 1,5” y 4,0” (3,8 y 10,2 El interruptor PTO (toma de fuerza) acopla y desacopla accesorios que utilizan PTO. Para acoplar PTO, tire hacia cm).
Page 98
Contador horario El contador horario (Figura 3) mide la cantidad de horas que la llave lleva puesta en la posición de ENCENDIDO. El contador horario hará parpadear la luz del indicador de cambio de aceite inicial a las 5 horas de uso y un recordatorio de lubricación cada 50 horas.
1. Remueva la varilla indicadora de nivel de aceite (A, técnico de Sears. Figura 5) y límpiela con un trapo limpio. Prueba 5: Revise la opción de corte de césped marcha 2.
Page 100
Alta altitud Para altitudes superiores a 5.000 pies (1.524 metros), es aceptable el uso de gasolina con un mínimo de 85 octanos/85 AKI (89 RON). Para cumplir con las emisiones, se requiere hacer un ajuste para alta altitud. Si la operación se realizar sin haber hecho éste ajuste se causará...
Page 101
1. Limpie el área de la tapa de combustible de polvo y 1. Compruebe el nivel de aceite. Cómo Consulte la sección desechos. Retire la tapa de combustible (A, Figura 6). verificar/añadir aceite. 2. Asegúrese de que los controles del arranque del equipo 2.
Page 102
ADVERTENCIA El motor se apagará si presiona el pedal de la velocidad de avance marcha atrás mientras la toma de fuerza está activada y el corte de césped marcha atrás no se ha activado. El operador siempre debe apagar la toma de fuerza antes de cruzar calles, caminos o cualquier zona por donde puedan transitar otros vehículos.
Page 103
Enganche de un remolque Ajustar la altura de corte del cortacésped La fuerza de tracción horizontal máxima permitida es de 444 La altura de corte puede ajustarse entre 1,5” y 4,0” (3,8 y Newton. La fuerza de tracción vertical máxima permitida 10,2 cm).
MANTENIMIENTO Underhållsschema TRACTOR Y CORTACÉSPED MOTOR Var 8:e timma eller en gång per dag Första 5 timmarna Cambio del aceite del motor - consulte el manual del Revisar el sistema de bloqueo de seguridad motor Limpiar el tractor y el cortacésped Var 8:e timma eller en gång per dag Limpiar los desechos del compartimento del motor Comprobación del nivel de aceite del motor - consulte...
Page 105
Sears. NOTIFICACIÓN: Cerciórese de seguir los pasos a continuación. De lo contrario podrían producirse daños en el sistema.
Page 106
Figura 13 Cómo cambiar el aceite Tapón de drenaje de aceite estándar Esta unidad no tiene un freno que se pueda ajustar man- 1. Remueva el tapón de drenaje de aceite (B, Figura ualmente. Si el freno no funciona correctamente, hable 13).
Page 107
Cambie el filtro de aceite Aprovisionamiento de aceite Para saber cada cuánto requiere ser reemplazado, • Coloque el motor a nivel. consulte el cuadro de Mantenimiento. • Limpie el área de llenado de aceite de todo desecho. 1. Drene el aceite del motor. Consulte la sección Remo- •...
Page 108
Figura 16 Figura 15 Retirar la plataforma del cortacésped ADVERTENCIA Ponga el freno de estacionamiento, desacople el PTO, detenga el motor, y quite la llave antes de intentar de retirar la plataforma del cortacésped. 1. Aparque el tractor sobre una superficie dura y nivelada como son los suelos hormigón.
Page 109
4. Instale los pasadore de horquilla (A, Figura 17) y las arandela (B) que sujetan los soporte del cortacésped (C) al bastidor del tractor. Repita en el otro lado. 5. Tire la palanca de la polea tensora (A, Figure 16) para liberar la tensión de la correa.
Page 110
Sustitución de la correa del PTO Lubrique la plataforma del cortacéspedes Lubrique la plataforma del cortacéspedes en las ubicaciones WARNING mostradas en la Figura 20. To avoid damaging belts, do not pry belts over pulleys. Aparque el tractor sobre una superficie suave y nivelada como una entrada de hormigón.
Page 111
Ajuste del embrague de la toma de fuerza Verifique el ajuste del embrague de la toma de fuerza después del período inicial de 25 horas de despegue del motor y luego después de cada 250 horas de operación. También realice el procedimiento siguiente si el embrague resbala o no engancha, o si ha sido instalado un nuevo embrague.
Page 112
Prestar servicio a las cuchillas del cortacéspedes ADVERTENCIA Para su seguridad personal, no manipule las cuchillas afiladas del cortacéspedes con las manos descubiertas. El manejo descuidado o inadecuado de las cuchillas puede tener como resultado heridas graves. ADVERTENCIA LOOSEN Para su seguridad personal, cada uno de los tornillos de cabeza hexagonal de montaje de las cuchillas debe Figura 24 ser instalado con una arandela de cabeza hexagonal o...
Page 113
Almacenaje Sistema de combustible El combustible puede deteriorarse si permanece ADVERTENCIA almacenado durante más de 30 días. El combustible deteriorado hace que se acumulen depósitos de ácido Nunca almacene la unidad (con combustible) en una estructura cerrada y con poca y resina en el sistema de combustible o en las piezas ventilación.
Revise visualmente el cableado. Si los cables están raídos o rotos, consulte con el distribuidor autorizado. Solenoide o motor de arranque Póngase en contacto con el servicio técnico de Sears. defectuosos. Interruptor de interbloqueo de se- Póngase en contacto con el servicio técnico de Sears.
Page 115
Localización de fallas del tractor (continuación) PROBLEMA BUSQUE SOLUCIÓN El freno interno está desgastado. Póngase en contacto con el servicio técnico de Sears. El freno no se man- tiene. La conexión de la dirección está Póngase en contacto con el servicio técnico de Sears.
ESPECIFICACIONES MOTOR TRANSMISIÓN Briggs & Stratton Tipo Torsión hidrostática K46 Fluido hidráulico 20w 30 Premium Engine Oil Fabricado por Briggs & Stratton® Velocidades Hacia delante: 0-9,3 km/h (0-5,8 MPH) Modelo Professional Series ™ Velocidades a 3400 rpm Marcha atrás: 0-5,6 km/h (0-3,5 MPH) Caballos de fuerza 20 Gross HP @ 3400 +/- 100 rpm Fuerza de torsión...
Desgaste y deterioro normal de los acabados exteriores o sustitución de la etiqueta del producto. Esta garantía le otorga derechos legales específi cos y también podría ejercer otros derechos que varían de estado en estado. Sears Brands Management Corporation, Hoff man Estates, IL 60179...
Descuento del 10% sobre el precio normal de *La cobertura en Canadá varía en algunos artículos. servicio y piezas instaladas relacionadas no Para detalles completos, llame a Sears Canadá al cubiertas por el acuerdo; asimismo, 10% de 1-800-361-6665. descuento sobre el precio normal de chequeo de Servicio de Instalación Sears.