Page 1
PLEASE DO NOT RETURN THE PRODUCT TO THE STORE Due to MSpa's continuous product improvement process, MSpa reserves the right to change the specifications and appearance of its products, which may result in updates to the instruction manual without prior notice.
To guide you in your initial MSpa experience, we are pleased to present you with this instruction manual. Please read this manual carefully before using the product for the first time. We are delighted to welcome you to the MSpa family, and look forward to sharing with you the full spectrum of our expertise.
IMPORTANT SAFETY INSTRUCTIONS For your own safety and that of your product, make sure to follow the safety precautions below. Fail to follow the instruction may result in serious injury, property damage or death. Improper installation or operation will void the warranty.
Page 4
The plug of spa shall be more than 3.5m away from the pool. WARNING: WARNING: Spray head must not be used. WARNING: The outlet of Spa must not be connected to any tap or fitting other than those specified. WARNING: Electric installations should fulfill the requirements of local standards.
Page 5
A green coloured terminal or a terminal marked G, GR, Ground, Grounding, or the symbol* is located inside the electric box. To reduce the risk of electric shock, this terminal must be connected to the grounding means provided in the electric supply service panel with a continuous copper wire equivalent in size to the circuit conductors supplying this equipment.
Page 6
Warning Label Instruction Please carefully read the warning label at the first time you are going to use MSpa. Please post this warning label on where is at a distance to MSpa within 1.5m/5’, people in spa can see it clearly.
NOTE: The drawings are for reference only. Actual products may vary. Not to scale. Use accessories exclusively provided by MSpa for safety reasons. When ordering parts, be sure to quote the MSpa model number and description. * Only for Aurora...
FIRST USE AND SETUP PREPARATION Site preparation and requirements ● The spa can be installed indoors or outdoors in around 10 minutes by one or more persons. For household use only. ● The spa must be set up on a flat, smooth and supporting surface that is able to bear the maximum load of the filled spa with the listed maximum number of occupants.
NOTE: Lay out all the parts on the ground and make sure they are all accounted for. For missing or damaged parts contact the appropriate MSpa after-sales service center.
Page 10
U-NE021: For this model, a side bar is included in the package. Set up the wicker bar and place the supporting legs underneath the spa tub before filling the water. It helps keeping the oval spa in a proper shape after water filling and inflation. 1.
Buckle Lock Operation NOTE: Always keep the spa cover on to minimize heat loss when heating the water. Lock Unlock CONTROLLER OPERATION LED Display Heater Button Filter Button Bubble Button - Adjust the bubble level by pressing Timer Button the button (L1: 300W, L2: 500W, L3: 720W Up Button Down Button UVC Button...
Page 12
FILTRATION Press the FILTER button to turn the function on/off. The light turns to green when the function is activated. FILTER FILTER NOTE: The filtration system will automatically start when the heating, Ozone or UVC sanitizing system is activated. NOTE: After turning off the heating system, the filtration system will automatically stop in 30 seconds. Filter Cartridge Cleaning Reminder: When the FILTER button is flashing or displays red, the filter cartridge must be cleaned or replaced.
WATER MAINTENANCE AND CHEMICALS CAUTION: ALWAYS ENSURE THE SPA IS UNPLUGGED BEFORE BEGINNING ANY MAINTENANCE WORK TO AVOID THE RISK OF INJURY OR DEATH. FILTER CARTRIDGE MAINTENANCE 1. Inspect and clean the filter cartridge gently after each use. Follow the steps below: NOTE: Change the filter cartridge every 3-5 days, or if the filter cartridge remains soiled and discolored.
Water Treatment: It is good practice with an existing spa to keep all air jets open and valves closed to allow chemically treated water to flush through all pipework. ● Always follow the chemical manufacturer’s directions, and the health and hazard warning. ●...
Clean the parts and tubes that the water goes through 1. Add more water to the minimum line F1 shows 15s after pressing FILTER, HEATING or UVC 2. Clean the parts and tubes that water goes through 3. Contact the MSpa Service Center...
Page 16
SPA LEAKING Drainage valve is not closed completely Close the drainage valve. Contact the MSpa Service Center, if spa is still leaking Water leaks from the spa pool body Repair the leaking hole/split with the repair kit material...
Need help?
Do you have a question about the Aurora and is the answer not in the manual?
Questions and answers