Download
Share
Print this page
  1. Manuals
  2. Brands
  3. LIGHT MY BRICKS Manuals
  4. Lighting Equipment
  5. LEGO Ship In A Bottle 21313 Lighting Kit
  6. Instructions manual

LIGHT MY BRICKS LEGO Ship In A Bottle 21313 Lighting Kit Instructions Manual

Hide thumbs

Advertisement

Quick Links

Download this manual
Light My Bricks: LEGO Ship In A Bottle 21313
Lighting Kit
The following page is the instructions for the
Light My Bricks LEGO Ship In A
Bottle (21313) LED light kit.
If you run into any issues, please refer to the
online troubleshooting guide.
To ensure a trouble-free installation of your light kit, please read and follow
each step carefully. These instructions can be downloaded in PDF format
here
Please note: This page lists instructions for the LED light kit only. If you are
wishing to purchase the Light My Bricks LEGO Ship In A Bottle (21313) LED light

Advertisement

loading
Need help?

Need help?

Do you have a question about the LEGO Ship In A Bottle 21313 Lighting Kit and is the answer not in the manual?

Questions and answers

Subscribe to Our Youtube Channel

Related Manuals for LIGHT MY BRICKS LEGO Ship In A Bottle 21313 Lighting Kit

Summary of Contents for LIGHT MY BRICKS LEGO Ship In A Bottle 21313 Lighting Kit

  • Page 1 These instructions can be downloaded in PDF format here Please note: This page lists instructions for the LED light kit only. If you are wishing to purchase the Light My Bricks LEGO Ship In A Bottle (21313) LED light...

  • Page 2: Package Contents

    kit , please click here to view the product page Package Contents: 4x White 30cm Bit Lights 6x Blue 30cm Bit Lights 1x Multi Effects Board 1x 6-Port Expansion Board 1x 8-Port Expansion Board 2x 5cm Connecting Cables 1x AA Battery Pack 6x Adhesive Squares Important things to note: Laying cables in between and underneath bricks...
  • Page 3 CAUTION: Forcing LEGO® to connect over a cable can result in damaging the cable and light. Connecting cable connectors to Expansion Boards Take extra care when inserting connectors to ports of Expansion Boards. Connectors can be inserted only one way. With the expansion board facing up, look for the soldered “=”...
  • Page 4 Connecting cable connectors to Strip Lights Take extra care when inserting connectors to ports on the Strip Lights. Connectors can be inserted only one way. With the Strip Light facing up, ensure the side of the connector with the wires exposed is facing down. If a plug won’t fit easily into a port connector, don’t force it.
  • Page 5 OK, Let’s Begin! 1.) First remove the bottle from the stand and disconnect the bottle top as well as top window sections to allow us to remove the ship.
  • Page 6 2.) Remove the three masts from the ship, then disconnect the following sections around the front:...
  • Page 7 3.) Take a White 30cm Bit Light and thread the connector end of the cable through the gap of the brown clip on the back of the ship. Thread it all the way through until the Bit Light is up against the edge of the gap. Ensure the LED is facing up, then lay the cable down the side of the ship as shown below.
  • Page 8 4.) Take another White 30cm Bit Light and slightly bend the wire down about 1cm from the top of the Bit Light as shown below. Hook the bit light over the following stud, then secure it in place by reconnecting the brown grill tile over the top.
  • Page 9 Lay the cable down in between studs, then reconnect the side brown wall tile. Repeat this process to install another White 30cm Bit Light to the left, securing it in place by reconnecting the brown tile over the top.
  • Page 10 5.) Before reconnecting the brown wall tile, slide in the 1×6 plate as shown below. You may need to slightly lift up the two bit lights to reconnect the plate back in place. Reconnect the brown wall tile by sliding it in and connecting it underneath, then reconnect the last remaining section to the back of the ship.
  • Page 11 Reconnect the three masts then group the three cables together and twist/wind them around each other a few times at the top to lock them in place. 6.) Take the AA Battery Pack and insert 3x AA Batteries to it. Connect the battery pack cable to the first port on the 6-Port Expansion Board.
  • Page 12 Note: If you experience any issues with the lights not working and suspect an issue with a component, please try a different port on the expansion board to verify where the fault lies (with the light or expansion board). To correct any issues with expansion board ports, please view the section addressing expansion board issues on our online troubleshooting guide.
  • Page 13 7.) Take two trans light blue round plates from inside the bottle then take out a Blue 30cm Bit Light and place it directly over one of studs. Secure the Bit Light in place by reconnecting the other trans light blue round plate over the top as shown below: Repeat this step to install another 5x Blue 30cm Bit Lights using more of the...
  • Page 14 trans light blue round plates from inside the bottle to secure them in place. Take the 8-Port Expansion Board and connect the AA Battery Pack to it, then connect all six Blue Bit Light cables. Turn ON the battery pack to test all the blue lights are working OK.
  • Page 15 Note: If you experience any issues with the lights not working and suspect an issue with a component, please try a different port on the expansion board to verify where the fault lies (with the light or expansion board). To correct any issues with expansion board ports, please view the section addressing expansion board issues on our online troubleshooting guide.
  • Page 16 Mount the LEGO plates with Bit Light to the base of the bottle as shown below, then thread the connector end of the cable through the lower gap of the bottle. Pull the cable all the way out from behind. We will now install the remaining five Blue Bit Lights around the base of the bottle.
  • Page 17 we did for the first Blue Bit Light.
  • Page 18 9.) Turn the bottle around to the back, then ensure all cables inside the bottle are laid away from the brown plates except for the two cables shown below. Lay these two cables in between the brown plates.
  • Page 19 Twist/wind the six cables around each other all the way to the ends so they come together to form one larger cable, then starting with the shorter two cables, connect all six cables to the 8-Port Expansion Board.
  • Page 20 Group all the cables closest the expansion board and twist/wind them around the larger cable so they group together. 10.) Pour back in, all of the trans light blue round plates into the bottle. Spread the pieces out evenly to try and cover the cables inside, then turn the bottle back around to the front.
  • Page 21 Take the ship and thread the group of three cables through the gap on the left of the blue bit light cables. Pull the cables all the way out from behind to then allow you to reconnect the ship back inside the bottle.
  • Page 22 11.) Reconnect all the trans clear sections which make up main section of the bottle.
  • Page 23 12.) Take a White 30cm Bit Light and with the cable facing down, place it over the centre of the studs on top of the main bottle section. Secure the Bit Light in place by reconnecting the bottle top section.
  • Page 24 Bring the other end of the cable across to the right, then twist/wind it around the group of white 30cm bit lights (on the right side). Connect the bit light to the next port on the 6-Port Expansion Board.
  • Page 25 Twist/wind any remaining excess cables around the larger group of cables as shown below: 13.) Take a Multi Effects Board and connect a 5cm Connecting Cable into one of the OUT ports (side with two ports). Connect the other end of the 5cm Connecting Cable to a spare port on the 8-Port Expansion Board.
  • Page 26 Take another 5cm Connecting Cable and connect it to the IN port on the Multi Effects Board (side with one port). Connect the other end of the 5cm Connecting Cable to a spare port on the 6-Port Expansion Board, then connect the AA Battery Pack to the remaining Port.
  • Page 27 14.) We can now set the effect we want. For a slow effect to represent ‘waves of the sea’, we chose to the ‘Pulse’ effect. Flick the switch to the far right for ‘Pulse’, then turn the speed wheel all the way to the left for the slowest speed. Alternatively, you can set whichever effect and speed you desire by simply changing the channel switch and adjusting the speed wheel.
  • Page 28 This finally completes installation of the Light My Bricks Ship in a Bottle Light Kit. We thank you for purchasing this product!

This manual is also suitable for:

Lmb 921313