Advertisement
Available languages
Available languages
Introduction
Technical Data
Advice for your
safety
Measured sound
value
Measured
vibration value
Use
Mains
connection
ENGLISH
You have high standards and expect to purchase quality goods – quality offered by
AEG. We have built a durable and reliable electric power tool for you.
Please read the instructions for use before first operation so you can handle your
power tool effectively and safely. We are sure that buying an Electric Power Tool
from AEG was the right choice!
Nominal power consumption of the
driving motor
. . . . . . . . . . . . . . . . . . . . . . . . .
Power consumption of the magnet
No-load speed
. . . . . . . . . . . . . . . . . . . .
Speed under load max.
Stroke
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
Stand height min.
Stand height max.
(carriage in top position)
Size of magnetic foot
Max. magnetic power
Drill diameter max. with core hole drill bit
Material thickness max.
Spindle receiver
Weight
. . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . .
The data stated above apply for models with 230 – 240 V.
In case of deviating mains voltage, the data stated on the rating plate are
applicable.
J Please pay attention to the safety instructions in the attached leaflet!
J Always use the protective shields on the machine.
J Always wear goggles when using the machine. It is recommended to wear gloves,
sturdy non slipping shoes and apron.
J Sawdust and splinters must not be removed while the machine is running.
J Do not pierce the motor housing as this could damage the double insulation (use
adhesives).
J Always disconnect the plug from the socket before carrying out any work on the
machine.
Only plug-in when machine is switched off.
J Keep mains lead clear from working range of the machine. Always lead the cable
away behind you.
J Secure the magnetic drill stand with the provided chain when working slanting or
vertical surfaces, or overhead such that it won't fall down in case of power loss.
J The maximum retaining power is reached when using steel with a low carbon
content and a material thickness of at least 12 mm.
J Do not expose the drill stand to rain and do not use in damp or non–flameproof
rooms.
Typically the A-weighted sound pressure level of the tool is 83 dB (A).
The noise level when working can exceed 85 dB (A).
Wear ear protectors! Measured values determined according to EN 50 144.
Typically the hand-arm vibration is below 2.5 m/s
Measured values determined according to EN 50 144.
The drill stand is suited for drilling large holes in steel and other ferroginous metals.
It is possible to use the magnetic drill stand while arc–welding.
Do not use this product in another way as stated for normal use.
Connect only to a single-phase AC current supply and only to the mains voltage
specified on the rating plate. Connection to sockets without earth protection is
possible as the appliance features protective insulation to DIN 57 740/ VDE 0740
and CEE 20. Radio suppression complies with the European standard EN 55014.
When fitting the plug, make sure that the brown (live) wire of this appliance is
connected to the plug terminal marked L or coloured red, and the blue (neutral) wire
of this appliance is connected to the plug terminal marked N or coloured black.
Under no circumstances must the wires of this appliance be connected to the earth
terminal of the plug marked either E, with the earth symbol or coloured green or
green/yellow.
1
. . . . . . . . .
. . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . . .
. . . . . . . . . . . . . . . . .
1/2"x20 Gg
1200 W
50 W
-1
300–640 min
-1
170–330 min
120 mm
410 mm
530 mm
160x80 mm
10 kN
. . .
42 mm
50 mm
10 kg
2
.
MDE 1200
Advertisement
