Advertisement
Available languages
Available languages
instructions to operate the power tool. Power
tools are dangerous in the hands of untrained
users.
1.4.5. Maintain power tools. Check for
misalignment or binding of moving parts,
breakage of parts and any other condition
that may affect the power tool's operation. If
damaged, have the power tool repaired before
use. Many accidents are caused by poorly
maintained power tools.
1.4.6. Use the power tool, accessories
and tool bits etc. in accordance with these
instructions, taking into account the working
conditions and the work to be performed. Use
of the power tool for operations different from
those intended could result in a hazardous
situation.
1.4.7. Noise&Vibration Information.
Measured
sound
according
to
EN
A-weighted noise levels of the product are:
Sound pressure level 95 dB(A);
Sound power level 108 dB(A).
Uncertainty K=3 dB.
Wear hearing protection!
Vibration total values (triad vector sum)
determined according to EN 61029:
Vibration emission value ah =3.80 m/s2
Uncertainty K =1.5 m/s2.
The vibration emission level given in this
information sheet has been measured in
accordance with a standardised test given
in EN 61029 and may be used to compare
one tool with another. It may be used for a
preliminary assessment of exposure. The
declared vibration emission level represents
the main applications of the tool. However if
the tool is used for different applications, with
different accessories or poorly maintained,
the vibration emission may differ. This may
significantly increase the exposure level
over the total working period. An estimation
of the level of exposure to vibration should
also take into account the times when the tool
is switched off or when it is running but not
actually doing the job. This may significantly
reduce the exposure level over the total
working period.
2. SPECIAL SAFETY INSTRUCTIONS
• Warning! The compressor may only be
used in suitable rooms (with good ventilation
and an ambient temperature from +5°C to
+40°C).
values
determined
61029.
Typically
• It is recommended to use the compressor
with a maximum operation of 70% in one hour
under full load, to allow for proper operation
of the product over time.
• Check that the tank is fully decompressed
before
connections
unscrewed.
• It is prohibited to make holes in, or welds
to, or purposely to distort the compressed air
tank.
• Do not perform any actions on the
compressor without first having taken the
plug out of the plug socket.
• Do not aim water jets or jets of flammable
liquids at the compressor.
• Do not place flammable objects near the
compressor.
• Switch the pressure regulator to the "0"
position (OFF = uit) during dwell time.
the
• Never aim the air jet at persons or animals
(fig. 20).
• Do not transport the compressor with the
tank pressurised.
• N.B.: some parts of the compressor such
as the head and the feed-through pipes may
reach high temperatures. Do not touch these
parts to avoid burns (fig. 12-13).
• Transport the compressor by lifting it or
by using the special grips or handles.
• Children and animals should be kept
far away from the area of operation of the
machine.
• If you use the compressor to spray paint:
a) Do not work in enclosed spaces or near
naked flames.
b) Make sure that the environment in which
you will be working has dedicated ventilation.
c) Protect your nose and mouth with a
dedicated mask.
• Do not use the compressor when the
electrical cable or the plug is damaged, and
instruct an authorised Support Service to
replace them with an original part.
• When the compressor is placed on a
surface higher than the floor, it should be
secured to prevent it from falling down during
operation.
• Do not put objects or your hands in the
protective
damage and damage to the compressor.
• Do not use the compressor as a blunt
instrument
against
animals in order to prevent serious damage.
• If the compressor is no longer in use,
with
the
covers
to
avoid
persons,
objects
11
tank
are
physical
or
Advertisement
