Subscribe to Our Youtube Channel
Related Manuals for Trumeter 924K
Summary of Contents for Trumeter 924K
-
Page 1: Output
924K Electronic Preset Counter with two presets Installation and Operating Instructions GlobalTestSupply www. .com Find Quality Products Online at: sales@GlobalTestSupply.com... -
Page 2: Table Of Contents
Table of Contents Preface Safety Instructions and Warnings Use according to the intended purpose Mounting in a control panel Electrical Installation Description Display/Operating elements Inputs INP A, INP B RESET GATE LOCK INPUT Outputs Output 1 Output 2 Active Outputs Programming Entering the programming Choice of main menus... -
Page 3: Preface
Mounting in a control panel Preface Mount the device away from heat Please read this instruction manual sources and avoid direct contact carefully before installation and start-up. with corrosive liquids, hot steam or Please observe all warnings and similar. CAUTION advice, both for your own safety and for general plant safety. -
Page 4: Description
Description T1-6 Decade key T1 … T6 6-digit multifunction LCD display Prog/Mode key Easy-to-read 2-line LCD-display with annunciators R Reset key for both the displayed preset and the status of the two outputs Current count value / main counter Simultaneous display of the actual value and of the Preset value/ Total count/ Batch counter presets or auxiliary counters Versions with/without backlit display... -
Page 5: Outputs
Outputs Entering a sub-menu The sub-menu is opened with the Output 1 Prog/Mode key and the first menu item is displayed. Relay with potential-free make (NO) contact or optocoupler with open emitter and collector Selecting the menu items Output 2 The Prog/Mode key is used to Relay with potential-free make (NO) contact or select a menu item within the... -
Page 6: Programming Menu
Pressing the Prog/Mode key 7.8.2 Table: Parameter Sets acknowledges this prompt and P.SEt 1 P.SEt 2 P.SET 3 terminates the programming; the modified settings are saved in Func Count Count Count the EEPROM. InP.PoL The text SAVE is FiLtEr displayed for 2 s Count Cnt.dir uP.dn... -
Page 7: Pulse Counter
7.8.4 Pulse Counter Quadrature x4 INP A: count input 0° INP B: count input 90° 7.8.4.1 Submenu for the Signal and Each pulse edge of INP A and Control inputs INP B will be counted. Menu for programming the signal Ratio measurement [A / B] and control inputs Inp A: count input A... - Page 8 Count mode SUBTRACT Count mode ADDING with Output 1 active when automatic reset and Total count status < preset value 1 counter Output 2 active when Output 2 (timed signal) active count status < 0 when main counter = preset Reset to preset 2 value 2 Automatic reset to zero when...
-
Page 9: Tacho/Frequency Meter
7.8.4.3 Submenu for configuration Manual reset (with red key) and electrical reset (reset input) Submenu for matching the input pulses and display No reset possible (red key and reset input inhibited) Multiplication factor Only electrical reset possible Multiplication factor can be (reset input) programmed from 00.0001 to 99.9999. - Page 10 Simple frequency 7.8.5.2 Submenu for configuration measurement Submenu for matching the input Inp A: Frequency input pulses and display Inp B: no function Differential measurement [A – B] Multiplication factor Inp A: Frequency input A Multiplication factor can be Inp B: Frequency input B programmed from 00.0001 to Total measurement [A + B] 99.9999.
-
Page 11: Timer
Lower line Inp A and Inp B: no function Display colour The timer is reset by means of a Upper line RESET (to zero when adding, to Lower line green valid edge, before zero is to be valid edge, before zero is to be Start: 1. - Page 12 Lock input main counter = preset value 2 Batch counter counts the number When the Lock input is activated of automatic repetitions of preset the programming is inhibited. Output 1 active when batch counter > preset 1 manual reset sets both counters When the Lock input is activated to zero the setting of the preset values is...
- Page 13 Tracking preset mode Display colour (for 6.92x.x1x3.xx0] Display colour When preset 2 is changed then upper line preset 1 automatically tracks it. lower line Reset to zero Preset 1 relative to preset 2 (see Display colour also section 17. Output upper line operations) lower line...
- Page 14 SUB mode output operations: 7.8.6.6 Submenu for Preset 2 permanent signal at Output 1, Submenu for Preset 2 becomes passive when count < Preset 1 ADD mode output operations: timed signal at Output 1, ADD mode output operations: becomes active when count > permanent signal at Output 2, Preset 1.
-
Page 15: Setting The Presets
Preset 2 and subsequently with negative direction and when count < Preset 2 SUB mode output operations: timed signal at Output 2, becomes passive with negative 7.9.2 Setting with Teach-In Function direction and when count < zero Program the MPI input to tEAch and subsequently with positive direction and when count >... -
Page 16: Connections
Connections N° Designation Function Collector 1 Output 1 10 Emitter 11 Emitter 2 Output 2 12 Not connected 13 Collector 2 14 AC: 90..260 VAC N~ Supply voltage DC: 10..30 VDC 15 AC: 90..260 VAC L~ Supply voltage DC: GND (0 VDC) 10 Technical Data 10.1 General Data... -
Page 17: Timer
10.4 Timer or NPN optocoupler Switching capacity 30 V DC/10 mA Seconds 0.001 s ... 999 999 s for IC = 10 mA: max. 2.0 V CESAT Minutes 0.001 min ... 999 999 min for IC = 5 mA: max. 0.4 V CESAT Hours 0.001 h .. -
Page 18: Scope Of Delivery
Preset counter Mounting clip Instruction manual 12 Ordering codes 6.924.X1XX.XX0 Ordering information: Input trigger levels EXAMPLE 924K 0 = Standard (HTL) Series A = 5V Operating Voltage Supply voltage A = 90 to 260 VAC 0 = 90 .. 260 VAC B = 10 to 30 VDC 3 = 10 .. -
Page 19: Frequencies (Typical)
13 Frequencies (typical) 13.2 Frequency meter HTL level 13.1 Pulse counter AC supply typ. Low 2,5 V HTL level typ. High 22 V AC supply typ. Low 2,5 V DC supply 12V typ. Low typ. High 22 V typ. High 10 V DC supply 12V typ. -
Page 20: Input Modes: Pulse Counting
14 Input modes: Pulse counting Function Diagram PNP: Count on rising edge NPN: Count on falling edge Note: No counting when GATE input is active P = Preset Cnt.Dir Inp A: Count input Inp B: Count direction Add: Display 0 --> Preset Sub: Display Preset ->... - Page 21 Function Diagram PNP: Count on rising edge NPN: Count on falling edge Note: No counting when GATE input is active Quad 4 A 90° B Inp A: Count input Count on rising and on falling edges Inp B: Count input Count on rising and on falling edges, Reverse direction...
-
Page 22: Input Modes: Timing
15 Input modes: Timing Function Diagram PNP: Count on rising edge NPN: Count on falling edge InA.InB Inp A: Start Inp B: Stop Add: Display 0 --> Preset Sub: Display Preset -> 0 InB.InB Inp A: no function Inp B: Start/Stop Add: Display 0 -->... -
Page 23: Input Modes: Frequency Meter
16 Input modes: Frequency meter Function Diagram PNP: Count on rising edge NPN: Count on falling edge Inp A: Frequency input Inp B: no function AsubB Inp A: Frequency input 1 Inp B: Frequency input 2 Formula: A - B AaddB Inp A: Frequency input 1 Inp B: Frequency input 2... -
Page 24: Output Operations
17 Output operations Mode Diagram Mode Diagram Only in the mode Additionally in the mode AddAr SubAr AddBat SubBat AddTot SubTot www.kuebler.com Seite 25 Page 25 GlobalTestSupply www. .com Find Quality Products Online at: sales@GlobalTestSupply.com... - Page 25 Mode Diagram Trail TrailAr www.kuebler.com Seite 26 Page 26 GlobalTestSupply www. .com Find Quality Products Online at: sales@GlobalTestSupply.com...
-
Page 26: Dimensional Drawings
18 Dimensional Drawings max. 10,5 Panel cut-out 15,5 4,25 Panel cut-out Fritz Kübler GmbH Zähl- und Sensortechnik P.O. Box 3440 D – 78023 Villingen-Schwenningen Germany Tel.: +49 (0) 77 20 – 39 03-0 Fax +49 (0) 77 20 – 2 15 64 sales@kuebler.com www.kuebler.com www.kuebler.com...
Need help?
Do you have a question about the 924K and is the answer not in the manual?
Questions and answers