Installing The New Refrigerator - Electrolux ETB2302J-A User Manual

R600A REFRIGERANT WARNING
• This appliance contains flammable R600a refrigerant.
Avoid safety hazards by carefully installing, handling,
servicing and disposing of this appliance. If your
appliance contains R600a it will be indicated on the
rating plate inside the appliance.
• Ensure that the tubing of the refrigerant circuit is not
damaged during transportation and installation.
• In the event any damage accidentally occurs, keep the
appliance away from open fires and any devices that
produce sparks or arcs and luminaries during normal or
abnormal operation, and unplug the appliance at the
power point. Call authorized service for necessary
action and advice.
• Leaking refrigerant may ignite vent area if leak occurs.
• The room for installing appliance must be at least 1m
per 8g of refrigerant. The amount and type of refrigerant
in the appliance can be found on the rating plate inside
the appliance.
• Do not damage the refrigerant circuit.
• Do not use electrical appliances inside the food storage
compartments of the appliance, unless they are of the
type recommended by the manufacturer.
• Keep ventilation openings, in the appliance enclosure or
in the built-in structure, clear of obstruction.
• Do not use mechanical devices or other means to
accelerate the defrosting process, other than those
recommended by the manufacturer.
WARNING
• Do not use a steam cleaner. If live components come
in contact with the condensing steam, they may short
circuit or cause an electric shock.
• Do not plug the appliance into a timer fitted to the
power point.
• Do not put your appliance on an uneven surface.
• Do not store explosive substances such as aerosol
cans with flammable propellant in the appliance.
• Do not store fizzy drinks in the freezer compartment.
• Never try to repair the refrigerator on your own. Use
only a qualified or authorised service person for repairs.
• Never use electric heaters or dryers to defrost the
freezer because you can receive an electric shock.
Installing Your New Refrigerator
Clean the refrigerator thoroughly according to instruction,
and wipe away any dust that has accumulated during
shipping.
Check that the floor is level. If it is not then adjust the
provided levelling leg so product is level and stable.
We recommend that you let your refrigertor run for two
to three hours before you put any food in it. This will allow
you to check that it is operating properly and that
enough cool air is going to the freezer.
4
OM Refresh III_VT.indd 12 OM Refresh III_VT.indd 12
Clearance around your Top and Bottom Mount refrigerator
• Allow a minimum of 30mm clearance on both sides of the
refrigerator.
• Allow 50mm clearance at the back of the refrigerator.
• Allow a minimum of 10mm clearance above the hinge cover.
• If you do not have a cupboard with allowance for air ow
above the refrigerator, the recommended clearance area on
top increases to 90 mm.
When positioned in a corner area, spacing of at 350mm on
•
the hinge side will allow the doors to open enough to enable
the removal of bins and shelves.
50mm
3
Recommended
airspace
CABINET
DOOR
NOTE: In installation where both sides and the rear of the
refrigerator are not enclosed by cabinetry eg the refrigerator
is placed against a wall, the clerance between the rear of
refrigerator and the wall should not be greater than 75mm.
You refrigerator uses energy efficient components that may
produce different noises (Refer "Noises" page for examples)
to your old refrigerator. Occasionally a gurgling sound of
refrigerator flowing or the sound of parts expanding and
contracting can be hard. These noises are quite normal.
Installing your refrigerator
1. Roll the refrigerator into place. The rollers are
designed for forward or backward movement only.
They are not castors. Moving the refrigerator
sideways may damage your floor and the rollers.
Before moving your refrigerator ensure height
adjusting nut and the stability foot are fully wound
up off the floor.
2. Wind the height adjusting nut under door hinge
down until the refrigerator is tilted back by 10mm
(see diagram).
Height adjusting nut
90 mm
10 mm
10 -15mm
Fixed rear rollers
7/6/2561 BE 09:25 7/6/2561 BE 09:25