Page 1
The following part is necessary to interface with the vehicle, to allow the remote start system to work properly. •SKIM Interface for Ram (DR) - Part #82209082 •SKREEM Interface for Dakota (ND) and Durango (HB) - Part #82209083 Technical Support...
Dodge Ram (DR) Durango (HB) and Dakota (ND) Remote Start Table of Contents Vehicle Preparation..................4 Module Preparation..................5 Component Installation................6 System Programming................12 System Testing..................16 Service Mode...................16 Reassembly....................17 Option Bank Chart...................18 Troubleshooting..................19 Changing Transmitter Batteries.............19 System Layout..................20 The soldering procedure illustrated below must be followed when perform- ing wire connections under the hood.
1/4” T-20 PARTS REQUIRED Part Number 82208859 5 AMP 1X 15 AMP 4X Part Number 82208863 (DR/HB) or 82208996 (ND) ® Vehicle Remote Start System Owner's Manual Featuring PowerCode Technology For the Ultimate in Comfort, Convenience and Security 2 sec.
Page 4
Overview The remote starter module harness will interface with the existing ignition switch connector, four center-splice connections, and a ground termination. Two wires will be routed through the cowl panel, to a hood-mounted safety switch and tachometer connection. Vehicle Preparation 1.
Module Preparation 1. Place fuses into the control module. A. Observe fuse amperage ratings. Place the 5 Amp fuse into the “Main B+” location. Populate the remaining fuse locations, as shown in the diagram, with the 15 1 2 3 Amp fuses.
Component Installation 1. Install Hood Safety Switch. A. Using (2) of the supplied 1/4” screws, secure hood safety switch on driver’s side rear corner of hood 1 2 3 1 2 3 per the diagram. Note: Wire exits top of switch. Switch must be bent at 45 degree angle.
Page 7
E. Run the harness White/Tan wire to the brake switch. Center-Splice Procedure Ram (DR) - center-splice to White/Tan wire in cavity #2 of the 6-way brake connector. Durango (HB) - center-splice to White/ Tan wire in cavity #2 of the 6-way brake connector.
Page 8
F. Run the White/Green wire to the headlight switch. Gently pull on the dash assembly to access the rear of the headlight switch. Ram (DR) - Connect the supplied 1 2 3 White/Green jumper wire into the harness White/Green wire and...
Page 9
J. For gas engines route the Blue/Green wire to the top of the engine at the coil connection point as shown. Ram (DR) - center-splice the Blue/ Green wire to the Blue/Green wire at the coil. Solder the connection. Durango (HB) - center-splice the Blue/Green wire to the Lt Blue/Red wire or Green/White wire at the coil.
Page 10
(sold seperately), to interface with this system. Ram (DR) - Part # 82209082 SKIM Sentry Key Interface Durango (HB) and Dakota (ND) - Part # 82209083 SKREEM Interface A. Remove the screw securing the SKIM/SKREEM module to the ig- nition cylinder.
Page 11
4. Install SKIM/SKREEM Interface, continued. D. Remove the remaining backing on the tape and position the antenna loop on the tape around the SKIM/ SKREEM transceiver antenna coil, with the stripe side facing out to- wards the key opening. Press down on antenna coil to ensure a strong bond.
System Programming Notes: 1. Reconnect the negative battery terminal prior to programming. 2. Up to a total of 8 transmitters can be programmed into memory. 3. Transmitters shipped with complete kits are pre-programmed to the DNA and do not need to be programmed at this time. 1.
Page 13
Option Programming - continued. C. Press and release the brake pedal. The horn will chirp and the lights will flash 1 time indicating the system is at option 1. Additional press and releases of the brake pedal will advance to the next option. The horn will chirp and the lights will flash according to which option is selected (i.e.
Page 14
4. Tach Rate Programming (Required for system to operate). A. Close hood. B. Turn the ignition to the “on” position. C. Press and hold the programming button. After 10 seconds the horn will chirp and the lights will flash 3 times. D.
Page 15
5. SKIM/SKREEM Transponder Interface Programming. 2 programmed Sentry keys are required for this step! NOTE: Review and understand steps A-J prior to performing. A. Close hood. B. Insert one of the two valid Sentry Keys into the ignition switch and turn the ignition switch to the “on”...
System Testing 1. Use the following checklist to ensure all features function as indicated. Remote start - Press start button 2X. Remote stop - Press and hold start button for 2 seconds. Hood safety switch shutdown - While under remote start, open hood - engine should shut down. Brake safety shutdown - While under remote start, press brake - engine should shut down Key-in-sense circuit - With key in the ignition cylinder, remote start should not activate.
Reassembly 1. Module & Harness mounting. A. Disconnect battery (if air bag equipped). B. Using supplied wire ties, secure the remote start module to existing wire harnesses under the left side of the dash. C. Using supplied wire ties, secure the SKIM/SKREEM Interface module to an existing wire harness under the dash.
Page 18
Option Bank Chart --------------------------------------------------------------------------------------------------------------------- Option Bank #1 (4 chirps) Factory Setting --------------------------------------------------------------------------------------------------------------------- 1. Not used Reserved for future upgrade feature......... .On 2. Not used Reserved for future upgrade feature......... .On 3. Tach diagnostic mode This feature should only be used for troubleshooting purposes only!...............Off 4.
8 consecutive times until the vehicle key is used. A. Start vehicle with the ignition key to reset. Changing the Remote Control Battery; Mopar part # 05140773AA: 1. With a small flathead screwdriver, carefully pry the two halves of the remote transmitter apart.
Page 20
DODG E R A M (DR ), DUR A NG O (HB ) and DA K OT A (ND) S Y S T E M L A Y OUT B LAC K HE ADLIG HT S WIT C H C ONNE C T OR...
Page 21
La pièce suivante est nécessaire pour interfacer avec le véhicule afin de permettre le bon fonctionnement du système de démarrage à distance. •Interface SKIM pour Ram (DR) – Pièce nº 82209082 •Interface SKREEM pour Dakota (ND) et Durango (HB) – Pièce nº 82209083...
Page 22
Démarreur à distance pour Dodge Ram (DR) Durango (HB) et Dakota (ND) Table des matières Préparation du véhicule.................24 Préparation du module..................25 Installation des composants................26 Programmation du système................32 Test du système..................36 Modes spéciaux...................36 Remontage....................37 Tableau des séries d’options.................38 Recherche des pannes.................39 Changer les piles de l’émetteur..............39...
Page 23
1/4” T-20 PIÈCES REQUISES Pièce numéro 82208859 5 AMP 1X 15 AMP 4X Pièce numéro 82208863 (DR/HB) ou 82208996 (ND) ® Vehicle Remote Start System Owner's Manual Featuring PowerCode Technology For the Ultimate in Comfort, Convenience and Security 2 sec.
Aperçu Le faisceau du module du démarreur à distance interfacera avec le connecteur du contacteur d’allumage existant, quatre connexions par épissure centrale et une mise à la masse. Deux fils seront acheminés à travers le panneau d’auvent, vers un interrupteur de sécurité monté sur le capot et la connexion du tachymètre. Préparation du véhicule 1.
Préparation du module 1. Placez les fusibles dans le module de commande. Respectez les calibres en ampères des fusibles. Placez le fusible de 5 A à l’emplacement portant la men- tion « Main B+ » (B+ principal). 1 2 3 1 2 3 Remplissez les logements restants, 1 2 3...
Installation des composants Installez l’interrupteur de sécurité du capot. A. À l’aide de (2) des vis de 1/4" fournies, fixez l’interrupteur de sécurité du capot sur le coin arrière du capot côté 1 2 3 conducteur, comme le montre le 1 2 3 4 schéma.
Page 27
1 2 3 4 E. Acheminez le fil blanc/bronze du faisceau vers l’interrupteur du frein. Ram (DR) - Connectez par épissure centrale au fil blanc/bronze de l’alvéole Procédure d’épissure centrale nº 2 du connecteur du frein à 6 broches.
Page 28
à l’arrière du commutateur 1 2 3 des phares. 1 2 3 Ram (DR) – Raccordez le fil de connexion blanc/vert fourni au fil blanc/vert du faisceau et connectez par épissure centrale au fil blanc/vert du véhicule dans l’alvéole nº 8 du connecteur des phares à...
Page 29
. Ram (DR) – Connectez par épissure centrale le fil bleu/vert au fil bleu/vert au niveau de la bobine. Soudez la connexion. Durango (HB) – Connectez par épissure centrale le fil bleu/vert au fil...
Page 30
Sentry Key, il faudra installer une pièce supplémentaire (vendue séparément) pour interfacer avec ce système. Ram (DR) – Pièce nº 82209082 SKIM Interface pour les clés codées Sentry Key Durango (HB) et Dakota (ND) - interface SKREEM Pièce nº 82209083 A.
Page 31
4. Installez l’interface SKIM/SKREEM, suite. D. Retirez le support restant du ruban adhésif et positionnez la boucle de l’antenne sur le ruban adhésif entourant la bobine de l’antenne de l’émetteur-récepteur SKIM/ SKREEM, la face striée faisant face au logement de la clé. Appuyez bien sur la bobine de l’antenne pour assurer une bonne adhérence.
Programmation du système Remarques : 1. Rebrancher la borne négative de la batterie avant d’effectuer la programmation. 2. Il est possible de programmer un total de 8 émetteurs. 3. Les émetteurs livrés avec des trousses complètes sont préprogrammés sur l’ADN et ne nécessitent aucune programmation pour l’instant. 1.
Page 33
Programmation des options - suite. C. Appuyez sur la pédale de frein puis relâchez-la. Le klaxon retentit et les phares clignotent 1 fois pour indiquer que le système se trouve sur l’option nº 1. Appuyez sur la pédale de frein et relâchez-la pour avancer jusqu’à l’option suivante. Le klaxon retentit et les phares clignotent le nombre de fois correspondant au numéro de l’option (ex.
Page 34
4. Programmation de la vitesse du tachymètre (indispensable au fonctionnement du système). A. Fermez le capot. B. Tournez le contact jusqu’à la position « ON ». C. Pressez et maintenez enfoncé le bouton de programmation. Dans un délai de 10 secondes, le klaxon émet 3 avertissements et les phares clignotent 3 fois.
Page 35
5. Programmation de l’interface du transpondeur SKIM/SKREEM. 2 clés codées Sentry Key sont requises pour cette étape! REMARQUE: étudier et bien comprendre les étapes A à J avant de com- mencer. A Fermez le capot. B. Introduisez l’une des deux clés codées Sentry Key valides dans le cylindre d’allumage et tournez le contacteur d’allumage jusqu’à...
Remontage 1. Montage du module et du faisceau. A. Débranchez la batterie (si le véhicule est équipé d’airbags). B. À l’aide des attaches autoblocantes fournies, fixez le module de démarrage à distance aux faisceaux existants situés sous la partie gauche du tab- leau de bord.
Tableau des séries d’options --------------------------------------------------------------------------------------------------------------------- ère série d’options (4 avertissements sonores) Réglage de l’usine --------------------------------------------------------------------------------------------------------------------- 1. Non utilisé Réservé à une option de mise à niveau future......Activé 2. Non utilisé Réservé à une option de mise à niveau future......Activé 3. Mode diagnostique du tachymètre Cette option doit être utilisée à...
A. Faites démarrer le véhicule avec la clé de contact pour réinitialiser. Changement des piles de la télécommande ; pièce Mopar nº 05140773AA : 1. Ouvrez avec précaution la télécommande en deux en faisant levier à l’aide d’un petit tournevis à...
Need help?
Do you have a question about the DR and is the answer not in the manual?
Questions and answers