Table of Contents
Advertisement
Advertisement
Table of Contents
Related Manuals for Silencer 56SL
Summary of Contents for Silencer 56SL
-
Page 2: Table Of Contents
Contents CHANGING THE BATTERY ............................3 STANDARD LCD ICON CONFIGURATIONS ......................... 4 LCD TRANSCEIVER REMOTE CONTROL OPERATION ....................4 Vehicle’s Status Check ..............................4 Second Vehicle Security Operation ..........................4 Voltage Check ................................4 Melody / Vibration Mode .............................. 4 Power Saver Mode .............................. -
Page 3: Changing The Battery
A. CHANGING THE BATTERY BATTERY REPLACEMENT: SLRF90A The Two-Way remote transmitter is powered by one “AAA” Battery. When the power of the battery weakens icon shall be displayed on the LCD screen. When the old battery is replaced, there will be beep sounds to indicate the power is back up on the transmitter. -
Page 4: Standard Lcd Icon Configurations
B. STANDARD LCD ICON CONFIGURATIONS: The lock icon will be displayed when The unlock icon will be displayed when the the door are locked. door are unlocked. Valet Mode System trigger All the function shall be temporally on hold Trunk Release Panic mode Engine Running Engine Cranking... -
Page 5: Power Saver Mode
Power Saver Mode: Press button 2 times first then press and hold buttons for 1 seconds until the beep confirms to enter Power Saver Mode, Under this mode press and hold button for 1 seconds until the beep confirms, then release SAVE SAVE the button to enable (The... -
Page 6: Chirp Indicators
E. CHIRP INDICATION PARKING LIGHT Chirp Function Parking light Function 1 Chirp Lock 1 Flash Lock 2 Chirps Unlock 2 Flashes Unlock 6 Chirps Car Locator 12 Flashes Car Locator Constant On Under Remote Start F. LOCK 1. Press the button on the transmitter. -
Page 7: Valet Mode
I. VALET MODE: When servicing or loaning your vehicle to others, the system should be placed in Valet Mode. Valet Mode prevents the system from remote starting functions. Enter Valet Mode: 1. Under the system unlocked, turn ignition “ON/ OFF/ ON” Press and hold valet switch for 2 seconds until the LED turns “ON”... -
Page 8: Trunk Release (Aux 1) Output
N. TRUNK RELEASE (AUX 1 / CH 1) OUTPUT Press and hold the button on the transmitter for 3 seconds to remotely control the will trunk release and the icon show on LCD screen. Aux 1 is a user-programmable timer output. You may program the built-in timer to send a ground signal for any time duration from 1 second to 90 seconds. -
Page 9: Second Car Operation
P. SECOND VEHICLE SECURITY OPERATION. You can be utilized to control a second vehicle’s keyless entry system. To program the remote control transmitter to a second vehicle, Press and hold the buttons 2 seconds to select car 2 or car 1 operation. 4 Button Remote Transmitter: For Car 2: When the LED start 2 pause flash then release buttons. -
Page 10: Remote Start Operation
LCD transceiver. B. Programmable Safety Start By default, your Silencer remote starter is programmed to start/stop after pressing the button 1 time. This default setting can be re-programmed to require 2 presses This setting is known as “Child Safety Mode”. -
Page 11: Running Time Extender
Running Time Extender User Programmable Run Time / Run Time Extension. The system has the ability to allow the user to extend the time the vehicle will be running under control of the remote start. This will only extend the run time back to the current run time setting during the current remote start cycle. -
Page 12: Disabling The Remote Start System
G. Disabling the Remote Start System: (If Installed) This feature allows your system’s remote start unit to be temporarily disabled to prevent the vehicle from being remote started accidentally. This feature is useful if the vehicle is being serviced or stored in an enclosed area. To disable the remote start, move the optional remote start enable toggle switch to the “OFF”... -
Page 13: Turbo Timer Mode
J. Turbo Timer Mode The built in turbo timer keeps the vehicle’s engine running for either 1, 3, or 5 minutes, after the vehicle key has been removed from the ignition. This feature will keep oil running through the turbo system to allow for appropriate cooling time. To activate: Step 1: While the vehicle is running, place the transmission in neutral, set the emergency / parking brake. -
Page 14: Group 1
GROUP 1 (One Flash of Parking Light) Chirps Shutdown Mode Solution • Close the hood. Hood Open • Check 14-pin White/Black wire connection. • Check 14-pin Black/White wire connection. Optional Enable Switch OFF or Black/ • Move the Enable Toggle Switch to “ON” position. (If installed.) White must have a ground Move the gear selector to “Park”/ “NEUTRAL”... -
Page 15: Lcd Remote Control Program Setting
L. LCD Remote Control Program Setting Enter: 1. Press and hold the button for 3 seconds until the text and a tone play to confirm is heard and then release. 2. Press button confirm the selection and move to the next setting, and the “Display”... - Page 16 SILENCER LIMITED LIFETIME WARRANTY Magnadyne Corporation or its authorized agents will, for the life of the vehicle and to the original purchaser, repair, replace or refund the retail sales price of said product or any part thereof, at the option of the Magnadyne Corporation or its authorized agents, if said product or part is found defective in materials or workmanship, when properly connected and operating on the correct power requirements designated for the specific product.
- Page 17 Magnadyne Corporation 1111 W. Victoria Street Compton CA 90220 (310) 735-2000 Please visit our website at www.magnadyne.com Made in Taiwan. All Rights Reserved...