System Operation & Instructions ................9 Section G. System Diagram....................16 Section H. Electrical Schematics ...................19 Section I. Disassembly/Assembly Instructions...............22 Section J. Systems Specifications..................24 Section K. Ordering Parts ....................24 Section L. Replacement Parts List ..................25 Section M. Terms & Warranty....................30 BUFFALO FILTER Smoke Evacuation Systems...
The fourth stage of filtration is an expanded foam and filtration media, both of which are also impregnated with a chemical agent, used to trap activated carbon fines from migrating out of the filter. U.S. Patent: #5,874,052 BUFFALO FILTER Smoke Evacuation Systems...
® 5. Change the ViroSafe filter at the prescribed number of hours for the filter being used. Failure to change the filter will affect the performance of the system. BUFFALO FILTER Smoke Evacuation Systems...
1, Clause 5.6 according to the mode of operation: Continuous Operation 8. The fuses used on the circuit board are to be serviced by an authorized Buffalo Filter technician as follows: 120V/60Hz, 100V/50 Hz & 60 Hz, 220V/50Hz and 240V/50Hz use a 0.0625A/250V fuse...
Page 7
CAUTIONS: • Using any other filters or accessories not manufactured by Buffalo Filter may cause damage to the system and will be cause for voiding the warranty. • DO NOT block either the tubing or the filter. If either becomes clogged or occluded, or if the airflow through either is significantly restricted, the motor/blower could overheat and cause the system to fail.
Please replace the filter if filter life has been expended. ONCE A WEEK: 1. Check the "Service" light on the membrane keypad. If the light is lit, contact Buffalo Filter for service instructions. 2. Check the filter for physical damage, fluid or solid contamination, and filter life. If filter life has been expended, please replace the filter.
There is no need to calibrate any part of the PlumeSafe Whisper 602 Smoke Evacuation System, all calibration is performed at the factory. If the "Service" light is illuminated at any time, contact your local distributor or Buffalo Filter for service instructions.
2. Replace ViroSafe filter 4. Motor/Blower obstructed 3. Check or replace hose 4. Contact your local distributor or Buffalo Filter 1. Smoke Evacuator System 1. Not plugged into electrical 1. Check power outlet or does not function even outlet or system not check to be sure system is though "ON"...
WARNING: If casual fluid is expected to be introduced into the ViroSafe Filter or PlumeSafe Whisper 602 system, fluid collection devices must be installed with the vacuum hose assembly. Failure to install a fluid collection device could cause filter blockage and electrical damage. BUFFALO FILTER Smoke Evacuation Systems...
Page 12
ON position. To turn the system electrical power OFF press the rocker switch to the OFF position. To turn the system motor ON, press the ON/OFF button on the membrane panel until the motor is running. To turn the system motor OFF, press the ON/OFF button again. BUFFALO FILTER Smoke Evacuation Systems...
Page 13
"trip" and the system will not operate. In order to re-start the system press the circuit breaker button into its original position. Note: On any Buffalo Filter smoke evacuator, there are two circuit breakers for the "hot" and "common" wires. Both circuit breakers act in the same manner. If either circuit breaker is tripped, press the circuit breaker button back into its original position.
Page 14
WHEN THE SERVICE LIGHT COMES ON, PLEASE CONTACT YOUR LOCAL DISTRIBUTOR OR BUFFALO FILTER FOR SERVICE INSTRUCTIONS ON THE SYSTEM BUFFALO FILTER...
Page 15
6. Press the UP or DOWN ARROWS of the vacuum adjust to the desired air suction. 7. Press the footswitch again to deactivate the system. If the footswitch is not in use, remove the footswitch and store away until needed again. BUFFALO FILTER Smoke Evacuation Systems...
Page 16
602 Service Manual Remote Switch Activator Installation/Operation The Buffalo Filter Remote Switch Activator (RSA1002) is designed for use with any brand of Electrosurgical Generator (ESU) that incorporates a Buffalo Filter Smoke Evacuation System. The RSA1002 operates essentially in the same manner as a footswitch; the smoke evacuator is turned on and off by pressing the "CUT"...
Page 17
Please refer to the instructions in the operator's manual provided with your Porta PlumeSafe Whisper 602 to properly change the filter. If any problems occur during in-service, please refer to Section E - Troubleshooting. BUFFALO FILTER Smoke Evacuation Systems...
Whisper ™ PlumeSafe® 602 Service Manual Section G. System Diagram Airflow through the PlumeSafe Whisper 602 BUFFALO FILTER Smoke Evacuation Systems...
Page 19
602 Service Manual PlumeSafe Whisper 602 Explosion View POWER F O O T SWITCH SUCTION CONTROL FILTER LIFE REMAINING 100% 80% 60% 40% 20% 0% FILTER LIFE REPLACE RESET SERVICE SMOKE EVACUATION SYSTEM Circuit Breaker BUFFALO FILTER Smoke Evacuation Systems...
Whisper ™ PlumeSafe® 602 Service Manual Section H. Electrical Schematics BUFFALO FILTER Smoke Evacuation Systems...
Page 22
Failure to install a fluid collection device could cause filter blockage and electrical damage. CAUTION: Using any other filter or accessory not manufactured by Buffalo Filter may cause damage to the system and will be cause for voiding the warranty. BUFFALO FILTER...
Please refer to the PlumeSafe Whisper 602 System diagram in the previous section for details. DISASSEMBLY INSTRUCTIONS In order to field service the Buffalo Filter PlumeSafe Whisper 602 Smoke Evacuation System, the system will need to be disassembled. Read the instructions below before attempting to service the system.
Page 24
REASSEMBLY INSTRUCTIONS For reassembly of the PlumeSafe Whisper 602 Smoke Evacuation System, please follow the above instructions in reverse order. Note: Refer to the Electrical Schematic in Section H for the correct wire terminations during assembly. BUFFALO FILTER Smoke Evacuation Systems...
602 Service Manual Section K. Ordering Parts Please order all parts, accessories and replacement filters for the PlumeSafe Whisper 602 by contacting your local distributor or Buffalo Filter directly at: 1-800-343-2324 (US only) 716-835-7000 (If calling internationally, use International Dialing Codes) FAX: 716-835-3414 E-mail: info@buffalofilter.com...
Label Kit for Whisper 602 LBL CITY LA Label for City of LA Approval BOX WHISPER Box for Whisper 602 System KEYPADBFGRFX Buffalo Filter Membrane Switch Graphics MEMBRANEBLNK Membrane Blank BOLT10-32 .5 Bolt 10-32 0.5" SS BOLT10-32.75 Bolt 10-32 0.75" Long BOLT6-32 .5"...
Page 28
Label Kit for Whisper 602 LBL CITY LA Label for City of LA Approval BOX WHISPER Box for Whisper 602 System KEYPADBFGRFX Buffalo Filter Membrane Switch Graphics MEMBRANEBLNK Membrane Blank BOLT10-32 .5 Bolt 10-32 0.5" SS BOLT10-32.75 Bolt 10-32 0.75" Long BOLT6-32 .5"...
Page 29
Label Kit for Whisper 602 LBL CITY LA Label for City of LA Approval BOX WHISPER Box for Whisper 602 System KEYPADBFGRFX Buffalo Filter Membrane Switch Graphics MEMBRANEBLNK Membrane Blank BOLT10-32 .5 Bolt 10-32 0.5" SS BOLT10-32.75 Bolt 10-32 0.75" Long BOLT6-32 .5"...
Page 30
Label Kit for Whisper 602 LBL CITY LA Label for City of LA Approval BOX WHISPER Box for Whisper 602 System KEYPADBFGRFX Buffalo Filter Membrane Switch Graphics MEMBRANEBLNK Membrane Blank BOLT10-32 .5 Bolt 10-32 0.5" SS BOLT10-32.75 Bolt 10-32 0.75" Long BOLT6-32 .5"...
RETURN OF MATERIAL. In the event of an error by Buffalo Filter, products may be returned to Buffalo Filter for correction of such error. In all other cases, returns will only be accepted with the prior consent of Buffalo Filter, in its sole discretion, and will be accepted only in exchange for merchandise of an equivalent dollar value, less a reasonable restocking and handling charge.