Advertisement
Quick Links
Operation Manual
Demolition Hammer
62296
Illustration similar, may vary depending on model
Read and follow the operating instructions and safety information before using for the first time.
Technical changes reserved!
Due to further developments, illustrations, functioning steps and technical data can differ insignific -
antly.
Updating the documentation
If you have suggestions for improvement or have found any irregularities, please contact us.
Advertisement
Related Manuals for WilTec 62296
Summary of Contents for WilTec 62296
- Page 1 Operation Manual Demolition Hammer 62296 Illustration similar, may vary depending on model Read and follow the operating instructions and safety information before using for the first time. Technical changes reserved! Due to further developments, illustrations, functioning steps and technical data can differ insignific - antly.
- Page 2 All rights reserved. The WilTec Wildanger Technik GmbH cannot be held accountable for any possible mistakes in this operating manual, nor in the diagrams and figures shown.
- Page 3 Level indicator Grease cap Gearbox Cylinder block Chisel retainer Locking bolt Chisel Exhaust pipe Protective cover Handle Spark plug Oil tank cap Ignition Gearbox cover Ventilation © by WilTec Wildanger Technik GmbH Item 62296 Page 3 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 4 To avoid damaging the individual parts, do not dismantle the demolition hammer, as this can impair the lifespan of the demolition hammer and lead to an increased risk of accidents. © by WilTec Wildanger Technik GmbH Item 62296 Page 4 http://www.WilTec.de...
- Page 5 After that re-close the retainer with the help of the locking bolt. 3. Fill the fuel tank with two-stroke mixture and press the primer in order to supply the system with fuel before then starting the motor. © by WilTec Wildanger Technik GmbH Item 62296 Page 5 http://www.WilTec.de...
- Page 6 If the lubricant level should drop beneath the red mark of the lubricant level gauge, make sure to refill it in order to guarantee the functionality of the tool. The lubricant level gauge should thereby be checked every 30 hours of usage. © by WilTec Wildanger Technik GmbH Item 62296 Page 6 http://www.WilTec.de http://www.aoyue.eu...
- Page 7 50 cm. Do not let the recoil start rebound freely and instead guide it back in order to protect the starter. Open the ventilation once the motor has been started. © by WilTec Wildanger Technik GmbH Item 62296 Page 7 http://www.WilTec.de http://www.aoyue.eu...
- Page 8 A clogged oil filter reduces the demolition hammer's working speed as well as its power of impact and does thereby not only affect its performance, but also increases the risk of the machine being dam- aged and its operator being injured. © by WilTec Wildanger Technik GmbH Item 62296 Page 8 http://www.WilTec.de...
- Page 9 Regularly perform maintenance on the exhaust pipe. Use a screwdriver in order to remove foreign matter and impurities. Lubricating the gearbox Open the gearbox cover in order to lubricate the eccentric shaft. The eccentric shaft should be lubric- ated in regular intervals. © by WilTec Wildanger Technik GmbH Item 62296 Page 9 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
-
Page 10: Troubleshooting
Clean the air filter. The device works fine, but the quality of the demolition is not sufficient The chisel is worn out. Resharpen and reforge or replace the chisel. © by WilTec Wildanger Technik GmbH Item 62296 Page 10 http://www.WilTec.de http://www.aoyue.eu... - Page 11 Weight (kg) 20.5 Capacity (cm³) Motor power (hp) Impact power (J) 20–55 Impact frequency (impacts/min) 700–1500 Carburettor type H119-6A-00-210 Spark plug type BM6A Starting system Recoil start © by WilTec Wildanger Technik GmbH Item 62296 Page 11 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 12 Check sharpness Chisel Sharpen and reforge Replace Check Silencer Remove deposits Check Cooling fins Clean Check/adjust electrodes dis- tance Spark plug Replace Check Screws and nuts Tighten © by WilTec Wildanger Technik GmbH Item 62296 Page 12 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 13 Needle bearing Fuel gasket 15×30×7 Bearing cover Straight pin 5×10 Screw M8×20 Left crankcase Sealing plug Screw M3×35 Tank cover Magnetic rotor Gasket Pressure spring Gearbox © by WilTec Wildanger Technik GmbH Item 62296 Page 13 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 14 Soft washer Screw M5×50 Lock sleeve Filter net Straight pin 4×18 Air filter seat Gearbox gasket Air filter cover Gearbox cover Screw M5×16 Screw M6×16 Washer 5 © by WilTec Wildanger Technik GmbH Item 62296 Page 14 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 15 © by WilTec Wildanger Technik GmbH Item 62296 Page 15 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 16 © by WilTec Wildanger Technik GmbH Item 62296 Page 16 http://www.WilTec.de http://www.aoyue.eu 2021-1 http://www.teichtip.de...
- Page 17 All WilTec electric devices that fall under the WEEE regulations are labelled with the crossed-out wheeled waste bin logo. This logo indicates that this electric equipment must not be disposed with the domestic waste.