Autojack iMIG200DP Safety And Operating Manual
  1. Manuals
  2. Brands
  3. Autojack Manuals
  4. Welding System
  5. iMIG200DP
  6. Safety and operating manual

Autojack iMIG200DP Safety And Operating Manual

Dual pulse mig welder
Hide thumbs
Table of Contents

Advertisement

Quick Links

SAFETY AND OPERATING MANUAL
Dual Pulse MIG Welder
iMIG200DP
ORIGINAL INSTRUCTIONS

Advertisement

Table of Contents
loading
Need help?

Need help?

Do you have a question about the iMIG200DP and is the answer not in the manual?

Questions and answers

Related Manuals for Autojack iMIG200DP

Summary of Contents for Autojack iMIG200DP

  • Page 1 SAFETY AND OPERATING MANUAL Dual Pulse MIG Welder iMIG200DP ORIGINAL INSTRUCTIONS...

  • Page 2: Table Of Contents

    TABLE OF CONTENTS Welcome to Autojack! Dear Customer, Congratulations on your purchase. Before using this product for the first time, please be sure to read these instructions for use. They provide you with all the information necessary for using the product safely and to ensure its long service life.

  • Page 3: General Power Tool Safety Warnings

    Do not expose power tools to rain or wet result in personal injury. conditions. Water entering a power tool will increase the risk of electric shock. iMIG200DP...
  • Page 4 Power tools are dangerous in the hands of untrained users. Use power tools only with specifically designated battery packs. Use of any other battery packs may create a risk of injury or fire iMIG200DP...
  • Page 5 Do not carry out any welding work on tanks that have been used to store gases, fuels, mineral oil or the like, even if they have been empty for a lengthy period of time, since any residue will result in a danger of explosion. iMIG200DP...
  • Page 6 (for earthing contact sockets max. 16 A fuses or 16 A circuit breakers). The use of too high a fuse may result in the cable burning and fire damage to the building. iMIG200DP...
  • Page 7 Do not store or use the equipment in wet conditions or in the rain. Use the equipment only indoors. iMIG200DP...

  • Page 8: Symbol Chart

    SYMBOL CHART iMIG200DP...

  • Page 9: Technical Specification/Package Contents

    Cooling Type Weight 14.4KG Dimensions 535*230*370 mm Package Contents  iMIG200DP Welder  3Mtr SN24 MIG Torch  1.8Mtr 300A Electrode Holder  1.2Mtr 300A Earth Clamp  Steel Liner  500g Hammer and Wood Brush  3 Gas Pipe Clamps ...

  • Page 10: Operation

    The pushing weld is when the torch is angled against the direction of the weld. The pulling weld is when your torch is angled towards the direction of the weld. The above listed techniques are both adequate for welding depending on your workpiece. iMIG200DP...
  • Page 11 If you would like to stick weld using this machine, you will need to set up the machine as pictured on the right. The electrode holder must be in the positive terminal and the earth clamp in the negative in order for this to work. iMIG200DP...

  • Page 12: Maintenance

     Make sure all cables are in good condition with no nicks or degradation to the sheathing  Regularly clear metallic dust from inside of the machine (use a low- pressure air gun)  Check all connections are usable with no oxidization or wear iMIG200DP...

  • Page 13: Troubleshooting

    Torch not connected Reconnect torch through torch correctly Gas pipe is blocked Check gas pipe or kinked Gas pipe broken Replace gas pipe Wire not feeding Different liner/wire Al/Al-Si/Al-Mg wire through feed roller needed requires a plastic liner and U roller iMIG200DP...

  • Page 14: Autojack Guarantee

    1.2.3 If asked to do so by Autojack or its Authorised Dealer, you return the product at your own cost to Autojack’s or the supplying Authorised Dealer’s Premises,...
  • Page 15 A good purchase to Autojack. If you include a Authorised Dealer should be able to contact number with this it will speed resolve the majority of these issues your claim up.
  • Page 16 This guarantee applies to all product 3.1 We only support products for purchased from an Authorised Dealer of Autojack within the United Kingdom. Terms domestic and private use. You agree of guarantee may vary in other countries. not to use the product for any...

  • Page 17: Declaration Of Conformity

    CE DECLARATION OF CONFORMITY Toolsave Unit C, Manders Ind Est., Old Heath Road, Wolverhampton, WV1 2RP. Declares that the iMIG200DP Welder is in compliance with the regulations included in the Directives: 2006/42/EC EC DECLARATION OF CONFORMITY Certificate for EC-type examination delivered by AV Technology Ltd.

  • Page 18: Machine Schematic

    1. LCD Colour Screen 9. Negative Socket 2. Home Button 10. Power Cord 3. Current Adjustment Knob 11.Power Switch 4. Inductance Control Knob 12. Cooling Fan 5. Voltage Adjustment Knob (MIG only) 6. Euro Torch Connection 7. Positive Socket 8. Air Plug iMIG200DP...

  • Page 19: Welding Spec Tables

    Welding Spec Tables The following tables are for reference only. For I-shaped butt welding: For flat head T-shaped welding: iMIG200DP...
  • Page 20 Welding Spec Tables For flat angle weld joints (thin plates): iMIG200DP...

Table of Contents