Cateye GE100 Instruction Manual

E-BIKE HEADLIGHT
HL-EB570G
Instruction Manual for
E-Bike Dealers
Design Pat. Pending
Copyright© 2020 CATEYE Co., Ltd.
1
HLEB570G-200924
• This instruction manual is intended for
use by E-Bike specialists.
Do not attempt to install this headlight if
you are not experienced with E-Bikes.
Consult your dealer for more information.
• After mounting the headlight, dealers are
expected to explain how to use the light
and to provide this instruction manual to
the customer.
WARNING!!!
• Make sure the illumination angle will not dazzle
oncoming traffic, and never position the visor to
the bottom of the headlight.
• Before your trip, please make sure the light is
firmly mounted to the bracket and it lights up.
CAUTION!
• Do not place it within children's reach.
• Do not remove the E-Bike adapter when the light
is on.
• Do not attach the E-Bike adapter if water
droplets, dust, or other foreign matter is attached
to the unit. Also, do not touch the terminals.
• Never use a high-pressure hose to clean the light.
• Always connect the front and rear light with the
2-core wire.
• The cable exits have to point downwards to keep
the housings waterproof.
• This device is rated IPX4 based on JIS C0920.
Do not immerse the device in water. Doing so
may cause a malfunction. Wipe off any moisture
after using the device in rainy weather.
• If the light unit or parts become dirty with mud,
etc., clean with a soft cloth which is moistened
with mild soap. Never apply paint thinner,
benzine or alcohol; damage will result.
LEGAL INFORMATION
Only road legal in Germany if installed on bicycles with
pedal assist function up to 25 km/h that are also
equipped with a battery charge indicator and function
to switch off the motor to prevent a deep discharge of
the battery to ensure that the lighting function is
available when needed.
SPECIFICATIONS
Light source High-brightness multi-white LED
Temperature range 14˚F – 104˚F (-10˚C – 40˚C)
Waterproof IPX4
E-Bike output compatibility
• Input voltage DC5.5 − 14.5 V
• Power consumption 6.8 W Nominal power(s)
• Cable length Approx. 150 cm (Red: Positive /
Black: Negative)
Dimensions/weight 2-9/16" x 2-31/64" x 51/64"
(65.0 x 63.0 x 45.5 mm) /
3.5 oz (94.5 g) (Light unit only)
* The specifications and design are subject to change without
notice.
GE100 FEATURES
ENG
K 1808 The GE100 headlight connects directly to the E-Bike drive unit for use. The headlight includes a visor to
direct the light distribution, allowing the unit to be mounted on the top or bottom of the handlebar. See
"Mounting above or below the handlebar" for how to change the mounting position of the E-Bike
adapter. The headlight can also be attached to a cartridge battery (optional) for use as a rechargeable
battery headlight. See "USING THE CARTRIDGE BATTERY (OPTIONAL)" for more information.
Light unit
Headlight
1
HOW TO MOUNT TO A BICYCLE
Mounted below
Mounted above
Mounting height :
400 – 1200 mm
2. Mounting above or below the handlebar
The head unit can be mounted on either above or below the
handle by positioning the visor of the head unit to the top.
Removing
Headlight
1
Turn the E-Bike adapter counterclock-
wise to separate the adapter from the
headlight and the bracket holder.
CAUTION!:
• When attaching or removing the E-Bike adapter, be sure to hold the headlight to prevent it from
dropping and becoming damaged.
• Do not attach the cartridge battery if water droplets, dust, or other foreign matter is attached to
the unit, and do not touch the terminals.
• Never position the visor to the bottom of the headlight. Doing so will dazzle oncoming traffic.
3. Attaching/removing the light
Mounting
Click
FlexTight™ bracket
Bracket holder
( H-34N )
E-Bike adapter
* This section explains how to mount the light unit
below the handlebar.
1. Mounting the bracket
Rubber pad
1
Strap
Bracket
Wrap the strap around Attach the dial.
the handlebar.
CAUTION!:
• Be sure to tighten the dial by hand. When you tighten it too hard with a
tool, the screw thread may be stripped.
• Check the dial and screw (*1) on the bracket periodically, and use them
without any loosening.
• Round off the cut edge of the bracket strap to prevent injury.
Mounting
Bracket holder
2
E-Bike adapter
Turn the bracket holder and align the grooves on the
E-Bike adapter to the grooves on the headlight, and turn
clockwise until the adapter stops.
Removing
Release button
Slide
Press and hold
Protective cover GP bracket
3
2
*1
Screw
Dial
Securely tighten the dial.
Mounted below Mounted above
Visor
3
4
NO!
Horizontal
OK
When mounting the light unit, ensure that
the light will not dazzle other road users.
To adjust the angle, loosen the dial or
the screw (*1) to the point that the
bracket moves slightly, make the
adjustment, and then tighten the screw
to fix the light unit in place.
Cut
Strap