Related Manuals for Gardner Denver Wittig SLS 34
Summary of Contents for Gardner Denver Wittig SLS 34
- Page 1 Operating Manual and Spare Parts List (Original Instructions) SLS 34-54 T-BA/ET-1250-0-GB September 2013...
-
Page 2: Table Of Contents
Contents Contents 1.0 Technical data ..........3 6.6 Troubleshooting ..........15 7.0 Maintenance..........17 2.0 Safety regulations ........... 5 7.1 Warranty............17 2.1 Proper use ............5 7.2 Maintenance, maintenance schedule.....17 2.2 Acceptance and monitoring......5 7.2.1 Cooling..........17 2.3 Hazard symbols and signs .......5 7.2.2 Rotary compressor/ 2.4 Pictographs used..........5 Compressor vacuum pump....18... -
Page 3: Technical Data
1.0 Technical data 1.0 Technical data Rotary compressor Parameters Unit Type SLS 34 Type SLS 54 Quantity of air with clear throughput Volumetric flow rate at an operating pressure of 2 bar gauge Intake temperature °C bar a (absolute) Intake pressure Maximum operating pressure bar g (gauge) Permissable Speed Range... - Page 4 1.0 Technical data Compressor vacuum pump Parameters Unit Type SLS 34 DV Type SLS 54 DV Quantity of air with clear throughput Volumetric flow rate with residual pressure 400 mbar / 60 % vacuum Maximum Operating Pressure with 4-way valve bar g (gauge) bar g (gauge) Maximum Operating Pressure...
-
Page 5: Safety Regulations
2.0 Safety 2.0 Safety 2.1 Proper use Danger! The rotary compressor, respectively the compressor pump, is exclusively intended for the compression, respectively the extraction of filtered air. Any other type of use is deemed to be improper. Attention Electricity! Proper use also includes compliance with the operat- ing data and the maintenance specified in the operat- ing manual. - Page 6 2.0 Safety • Alterations, attachments or conversions to the rotary compressor/compressor vacuum pump, which may affect safety, are not permitted without consulting the manufacturer. • All warnings on the machine must be observed and must be kept in a fully legible condition. •...
-
Page 7: Transport
3.0 Transport 3.0 Transport Symbols on the packaging: 3.3 Scope of supply Top! The content of the shipment is listed on the delivery note. Check immediately to ensure that the shipment is complete. Damage during shipment as well as errors can only be acknowledged provi- ded written notification is given without Fragile! delay. -
Page 8: Installation
4.0 Installation 4.0 Installation 4.1 General • balanced, as well as having the • smallest possible angle and must be as short as The air-cooled rotary compressor (SLS 34 / SLS 54) possible. and vacuum pumps (SLS 34 DV / SLS 54 DV) gene- rate pressure or vacuum. -
Page 9: V-Belt Drive
4.0 Installation 4.3.2 V-belt drive The tension setting for the V-belts must allow them to be depressed by about an inch. V-belt drive is recommended where the motor speed needs to be transformed or reduced. 4.3.3 Coupling drive Note nominal speed according to „1.0 see „Stationary operation“... -
Page 10: Vent Valve
4.0 Installation val, and may thus enter the compressor which would • The safety valve must be secured so as to prevent affect the dust removal by the presettling tank. unauthorized or mistaken manipulation. • The safety valve must not be blocked. It must be ensured that the arrow in the “TOP”... -
Page 11: Commissioning
5.0 Commissioning 5.0 Commissioning When commissioning the machine, the 5.7 Check operating parameters safety regulations (see „Safety“ Check pressure/vacuum, speed and temperature page 5.) and the additionally applicable according to the identification plate and technical data accident prevention regulations must be (see „Technical data“... - Page 12 5.0 Commissioning 10 Lever position “Pressurize” 7 Exhaust, respectively intake pipe (R 2”) 8 to Tank (R 2") DIAGRAM 7. Compressor T-BA/ET-1250-0-GB-10-11...
-
Page 13: Operation
6.0 Operation 6.0 Operation 6.1 Restarting Lube oil specification (see „Recommended lubricant“ on page 22.) The rotary compressor, respectively the compressor vacuum pump is normally started as specified in 6.2.1 Safety valve Chapter 5 “Commissioning”. In accordance with accident prevention regulations, a 6.2 Regular inspections safety valve without a cut-off must be fitted in the pres- sure pipe downstream of every compressor. -
Page 14: Possible Operating Errors
Operating errors can cause machine In the event of damage due to operating failure. errors, no warranty claim can be submit- ted to Gardner Denver. To be avoided at all costs: 6.4 Action for prolonged standstill • Clean the machine thoroughly. -
Page 15: Flushing After Excess Intake
The flushed out dirt could partly return to the intake side. 6.6 Troubleshooting Gardner Denver rotary compressors and compressor should arise, the summary below provides you with vacuum pumps, are noted for the low rate of wear of the possibility of being able to determine the cause the rotary slide valves during normal use. - Page 16 6.0 Operation Defect Possible cause Rectification Compressed air temperature too high • • Excessive final pressure Maintain nominal pressure • • Exhaust silencer blocked Replace exhaust silencer • • Change-over four-way cock in wrong Switch change-over four-way cock position correctly •...
-
Page 17: Maintenance
7.0 Maintenance 7.0 Maintenance 7.1 Warranty Please note that we accept no liability in the event of period can be extended if the specified number of failure to comply with the installation and operating operating hours is not achieved. manual. Due to the different operating conditions it is impossi- It should be noted that repairs on the rotary compres- ble to predict when the check up for wear, repairs,... -
Page 18: Rotary Compressor/Compressor Vacuum Pump
7.0 Maintenance 7.2.2 Rotary compressor/Compressor Assembling the filter vacuum pump Insert filter cartridge. The machine must be cleaned every week. Place gasket, respectively round seal in cover. Push washers outwards against the tapered or star knob. When washing respectively cleaning with a pressure washer, there is a risk of water penetration, which can cause water Push cover into the housing (on type SFA, turn cover... -
Page 19: V-Belt And Belt Tension
It must then be replaced at the Cleaning can consist of blowing or, alternatively knok- next opportunity. king. Gardner Denver accepts no liability for Cleaning by blowing damage due to failure to replace the fil- ter cartridge on time. -
Page 20: Check Valve
7.0 Maintenance Do not rinse the oil tank with solvent or When the amount of wear has reached 5 mm, the degreaser. rotary slide valves must be replaced (see the separate assembly instructions!). The initial inspections should take place after about 6 Do not forget to pre-lubricate (see „Prelubricate“... -
Page 21: List Of Spare Parts
8.0 List of spare parts 8.0 List of spare parts Keeping a stock of the most important spare parts at We recommend stocking the following wearing and the place of use is a major precondition for the con- spare parts according to the spare parts list: stant functional readiness of the compressor and Item Nos. - Page 22 Flat gasket 464 525 00 between parts 1 and 38 Only original parts from Gardner Denver When ordering the rotor, Item No. 3, and may be used. The warranty from Gard- the oil tank cover, Item No. 6, the specific ner Denver will become void if spare direction of rotation must be noted.
- Page 23 8.0 List of spare parts DIAGRAM 11. Longitudinal and cross-sectional diagram through the compressor vacuum pump with check valve T-BA/ET-1250-0-GB-10-11...
- Page 24 8.0 List of spare parts T-BA/ET-1250-0-GB-10-11...
- Page 25 8.0 List of spare parts DIAGRAM12. Longitudinal and cross-sectional diagram through the com- pressor vacuum pump with changeover four-way cock T-BA/ET-1250-0-GB-10-11...
- Page 26 Contact Us Americas Australia Belgium Gardner Denver, Inc. Gardner Denver Ind. Australia Pty Ltd Gardner Denver Belgium N.V. Industrial Products Group - Americas 30 Bearing Road Luithagen 7A 1800 Gardner Expressway Seven Hills Haven 200 Quincy, IL. 62305 New South Wales...