Page 1
Anleitung_TH_ID_1000_E_SPK7__ 01.04.14 07:14 Seite 1 Original operating instructions Impact Drill 1000 E TH-ID Art.-Nr.: 42.598.24 I.-Nr.: 11014...
Page 2
Anleitung_TH_ID_1000_E_SPK7__ 01.04.14 07:14 Seite 2 To avoid damaging the gearbox, the drill / hammer drill selector switch should only be moved when the machine is at a standstill...
Page 3
Anleitung_TH_ID_1000_E_SPK7__ 01.04.14 07:14 Seite 3...
Page 4
Anleitung_TH_ID_1000_E_SPK7__ 01.04.14 07:14 Seite 4...
Page 5
Anleitung_TH_ID_1000_E_SPK7__ 01.04.14 07:14 Seite 5 Danger! Read the operating instructions to reduce the risk of inquiry Caution! Wear ear-muffs. The impact of noise can cause damage to hearing. Caution! Wear a breathing mask. Dust which is injurious to health can be generated when working on wood and other materials. Never use the device to work on any materials containing asbestos! Caution! Wear safety goggles.
Anleitung_TH_ID_1000_E_SPK7__ 01.04.14 07:14 Seite 6 Danger! Danger! The equipment and packaging material are not When using equipment, a few safety precautions toys. Do not let children play with plastic bags, must be observed to avoid injuries and damage. foils or small parts. There is a danger of Please read the complete operating manual with due swallowing or suffocating! care.
Anleitung_TH_ID_1000_E_SPK7__ 01.04.14 07:14 Seite 7 Danger! Danger! Sound and vibration Residual risks Even if you use this electric power tool in Sound and vibration values were measured in accordance with instructions, certain residual risks cannot be rules out. The following hazards accordance with EN 60745.
Anleitung_TH_ID_1000_E_SPK7__ 01.04.14 07:14 Seite 8 Once a drill bit is secured in the chuck (see. 6.3), Tip: Start drilling holes at low speed. Then increase set the depth stop (2) to the same level as the the speed in stages. drill bit.
Anleitung_TH_ID_1000_E_SPK7__ 01.04.14 07:14 Seite 9 7.6.2 Drilling steel 9.2 Carbon brushes Switch the drill / hammer drill selector switch (3) In case of excessive sparking, have the carbon to position A (drill). brushes checked only by a qualified electrician. Always use HSS drill bits (HSS = high speed Danger! The carbon brushes should not be re steel) and a low speed setting for drilling steel.
Page 10
EÚ a noriem pre výrobok og standarder for artikkel A a cikkekhez az EU-irányvonal és Normák szerint a E Lýsir uppfyllingu EU-reglna og annarra staðla vöru következő konformitást jelenti ki Impact Drill TH-ID 1000 E (Einhell) 87/404/EC_2009/105/EC 2006/42/EC Annex IV 2005/32/EC_2009/125/EC...
Page 11
Anleitung_TH_ID_1000_E_SPK7__ 01.04.14 07:14 Seite 11 t For EU countries only Never place any electric tools in your household refuse. To comply with European Directive 2002/96/EC concerning old electric and electronic equipment and its implementation in national laws, old electric tools have to be separated from other waste and disposed of in an environment-friendly fashion, e.g.
Anleitung_TH_ID_1000_E_SPK7__ 01.04.14 07:14 Seite 12 t GUARANTEE CERTIFICATE Dear Customer, All of our products undergo strict quality checks to ensure that they reach you in perfect condition. In the unlikely event that your device develops a fault, please contact our service department at the address shown on this guarantee card.
Need help?
Do you have a question about the TH-ID 1000 E and is the answer not in the manual?
Questions and answers