Table of Contents
Advertisement
Available languages
Available languages
•
After you finish operating, switch the meat
grinder off, setting the switch (7) to the
position «0» and unplug the unit; after that
you can disassemble it.
MEAT PROCESSING
•
Press and hold the meat grinder head lock
button (5), insert the meat grinder head
(3) to the installation place (4) and turn
the meat grinder head (3) counterclock-
wise until bumping, release the button (5)
(pic. 1, 2).
•
Install the screw (8) into the meat grinder
head (3) body (pic. 3).
•
Install the crossed blade (9) (pic. 4).
•
Select one required plate (10 or 11) and set
it over the blade (9), matching the ledges
on the grate with the grooves on the meat
grinder head body (3), tighten the nut (12)
(pic. 5, 6, 7).
Attention!
Install the blade (9) with its cutting side fac-
–
ing the grate. If the blade (9) is installed
improperly, it will not grind the products.
Coarse grate (11) is for processing raw
–
meat, vegetables, dried fruit, cheese,
fish, etc.
The fine cutting plate (10) is suited for pro-
–
cessing both raw and cooked meat, fish etc.
•
Place the food tray (2) on the mouth of the
meat grinder head (3).
•
Insert the power plug into the mains socket.
•
Switch the meat grinder on by setting the
switch (7) to the position «ON».
•
During the operation use only the pusher (1)
(pic. 8).
Note:
For better meat processing, slice it in cubes
–
or stripes. Defrost frozen meat thoroughly.
During the operation use only the pusher
–
supplied with the unit; do not use any other
objects, do not push meat with your hands.
•
After you finish operating, switch the meat
grinder off, setting the switch (7) to the
position «0» and unplug the unit; after that
you can disassemble it.
•
To remove the meat grinder head (3), press
the release button (5), turn the meat grinder
head (3) clockwise and remove it.
IM VT-3631.indd 5
•
To disassemble the meat grinder head,
unscrew the nut (12) and take out the
installed plate (10 or 11), the blade (9) and
the screw (8) from the meat grinder head
body.
AUTO SWITCH-OFF FUNCTION
•
The meat grinder is equipped with an auto
switch-off function in case of motor unit
overheating.
•
In case of overheating of the motor, the
automatic thermal switch will be on, and the
meat grinder will switch off.
•
In this case immediately remove the power
plug from the mains socket.
•
Let the meat grinder cool down for approxi-
mately 50-60 minutes before switching it on
again (the unit can cool down longer if the
room temperature is high).
•
Plug the meat grinder into the mains, switch
it on, if the meat grinder can not be switched
on, this may mean that it is otherwise dam-
aged. In this case apply to any authorized
service center at the contact address list
given in the warranty certificate and on the
website www.vitek.ru for repairing the meat
grinder.
MEAT GRINDER CARE
•
After finishing operation, switch the meat
grinder off by setting the switch (7) to the
position «0», and unplug the unit.
•
Press the release button (5), turn the meat
grinder head clockwise and remove it.
•
Unscrew the nut (12) and remove the plates
(10 or 11) and the crossed blade (9) from
the screw (8).
•
Remove the screw (8) from the meat grinder
head (3).
•
Remove remains of food from the screw (8).
•
Wash all the parts of the meat grinder with
warm soapy water and a neutral deter-
gent, then rinse and dry thoroughly before
assembling.
•
Clean the meat grinder body (6) with
a slightly damp cloth and then wipe the
body dry.
•
Do not use solvents or abrasives to clean
the meat grinder body (6).
5
ENGLISH
31.01.2019 17:01:02
Advertisement
Table of Contents
