Chamberlain Security+ 940CD User Manual page 2

INSTALLATION
1. Choose a convenient
location for installation.
Install out of the reach of
children at a minimum
height of 5 feet (1.5m),
away from all moving
parts of door.
Test the reception of the
Keyless Entry by
operating your opener
from the selected
location. Change the location if necessary.
2. Remove the compartment cover to access the bottom mounting
hole. Slide the cover down to remove. Remove batteries.
3. Center the Keypad against selected location.
Mark the top centerline screw location and drill
1/8" pilot hole. Install top mounting screw, allowing
1/8" to protrude above surface. Position
keypad on screw head and adjust for snug fit.
Drill 1/8" pilot hole for the bottom mounting
screw. Complete installation with bottom screw,
using care to avoid cracking plastic housing. Do
not overtighten.
Reinstall batteries and replace the compartment cover.
To replace compartment cover insert the lip at the top and snap
it into place.
TO CHANGE AN EXISTING, KNOWN PIN
If the existing PIN is known, it may be changed by one person
without using a ladder.
1. Press the four buttons for the present PIN, then press and hold
the # button.
The opener light will blink twice. Release the # button.
2. Press the new 4-digit PIN you have chosen, then press ENTER.
The motor unit lights will blink once when the PIN has been
learned.
Test by pressing the new PIN, then press ENTER. The door should
move.
TO SET A TEMPORARY PIN
You may authorize access by visitors or service people with a
temporary 4-digit PIN. After a programmed number of hours or
number of accesses, this temporary PIN expires and will no longer
open the door. It can be used to close the door even after it has
expired. To set a temporary PIN:
1. Press the four buttons for your personal entry PIN (not the last
temporary PIN), then press and hold the ✽ button.
The opener light will blink three times. Release the
button.
2. Press the temporary 4-digit PIN you have chosen, then press
ENTER.
The opener light will blink four times.
3. To set the number of hours this temporary PIN will work, press
the number of hours (up to 255), then press ✽.
To set the number of times this temporary PIN will work, press the
number of times (up to 255), then press #.
The opener light will blink once when the temporary PIN has been
learned.
Test by pressing the four buttons for the temporary PIN, then press
Enter. The door should move. If the temporary PIN was set to a
certain number of openings, remember that the test has used up
one opening.To clear the temporary password, repeat steps 1-3,
setting the number of hours or times to 0 in step 3.
SPECIAL NOTE: The temporary password can ONLY be
programmed to keypads working on a Chamberlain, Craftsman
LiftMaster Garage Door Opener. It WILL NOT work on
keypads programmed to an external receiver.
The temporary password will continue to CLOSE the door even
after the time has expired.
To eliminate this, program a new temporary password into the
keypad.
114A3205B
Keyless Typical
Entry Installation
Exterior Front Wall
1-Piece or
Sectional Door
Door Jamb Edge
(Optional)
Door Jamb Face
(SECTIONAL DOOR ONLY
KEYLESS ENTRY MUST BE
INSTALLED WITHIN
SIGHT OF THE DOOR
Bottom
mounting
hole
Battery
Battery
Cover
OR
© 2006, The Chamberlain Group, Inc.
is a Registered Trademark of Sears, Roebuck and Co.
Craftsman ®
THE KEYLESS ENTRY BATTERY
To prevent possible SERIOUS INJURY or DEATH:
• NEVER allow small children near batteries.
• If battery is swallowed, immediately notify doctor.
The battery should produce power for at least
one year. Replace when the keypad illumination
becomes dim. Dispose of old batteries properly.
FOR SERVICE DIAL OUR TOLL FREE NUMBER:
1-800-654-4736
® or
All Rights Reserved
WARNING
CAUTION