Related Manuals for Wieland WIENET SDS Series
Summary of Contents for Wieland WIENET SDS Series
- Page 1 wienet SDS Industrial serial device server Manual Doc. no. BA000870 Last updated: 06/2020 (Rev. A)
- Page 2 Wieland Electric. wienet is a trademark of Wieland Electric. Other names may in this assembly manual mentioned product and brand trademarks or registered trademarks of their respective owners could be used, whose use by third parties for their own purposes could violate the rights of the owners.
-
Page 3: Table Of Contents
COM port overview 5.5.2 COM configuration 5.5.3 COM configuration: Advanced settings SNMP/ALERT settings E-Mail settings Log settings 5.8.1 System log settings 5.8.2 COM log settings 5.8.3 System log 5.8.4 COM log Wieland Electric GmbH | BA000870 | 06/2020 (Rev. A) - Page 4 Hardware Pin assignments of serial port 6.2.1 Pin assignments of serial interfaces LED indicators Software Emergency system recovery System recovery procedures Service and support Appendix List of figures List of tables Wieland Electric GmbH | BA000870 | 06/2020 (Rev. A)
-
Page 5: About This Manual
A T T E N TI ON Thus, read and follow all warnings carefully. N OT I C E This note provides you with tips and information regarding the handling of the product. Wieland Electric GmbH | BA000870 | 06/2020 (Rev. A) -
Page 6: Safety Instructions
It is recommended that you make a copy or backup of all major settings stored in the device memory. Any other application or change to the device – even during assembly and installation – will result in the invalidity of any warranty claims against Wieland Electric GmbH. Wieland Electric GmbH | BA000870 | 06/2020 (Rev. A) -
Page 7: Introduction
• Wide range power supply input either 5 VDC (DC Jack) or between 9 – 30 VDC (Terminal Block) • wienet SDS-xB with one COM port; wienet SDS2-TB with two COM ports Wieland Electric GmbH | BA000870 | 06/2020 (Rev. A) -
Page 8: Getting Started
Notify Wieland immediately if any of the above items is missing or damaged upon delivery. N OT I C E Appearance, front and rear panels The following figures show particular wienet SDS series device's front, back, side and top panels. wienet SDS – Industrial 1-Port Serial Device Server SDS-TB SDS-DB Wieland Electric GmbH | BA000870 | 06/2020 (Rev. -
Page 9: First Time Installation
Before installing the device, please follow strictly all safety procedures described in the installation instructions supplied with the product. Wieland will not be liable for any damages to property or personal injuries resulting from the installation or overall use of the device. Do not attempt to ma- nipulate the product in any way if unsure of the steps described there. -
Page 10: Factory Default Settings
LAN port for 5 seconds or follow the procedure in section 5.9.4 Backup/restore configura- tion, p. 33, to restore the wienet Industrial Serial Device Server to the factory default settings. Wieland Electric GmbH | BA000870 | 06/2020 (Rev. A) -
Page 11: Configuration And Setup
Configuration and setup CONFIGURATION AND SETUP Device-specific configurations can be carried out via Wieland's user-friendly web interface. Configuring through Web/CLI interface Every wienet SDS Industrial Serial Device Server is equipped with a built-in web server in the firm- ware. Therefore, the device can be accessed by using a web browser for configuration by entering the device's IP address (default IP address is 10.0.50.100) in the URL field of your web browser. - Page 12 This approach (web interface) for configuring your device is the most user-friendly. It is the most rec- ommended and the most common method used for wienet SDS Serial Device Server Series. Go to its corresponding section for a detailed explanation. Wieland Electric GmbH | BA000870 | 06/2020 (Rev. A)
- Page 13 You can simply check the DHCP (Obtain an IP Automatically) checkbox in the Network Set- ting dialog using Wieland's wienet Manager, a device management utility, and then restart the de- vice. Once restarted, the IP address will be configured automatically.
-
Page 14: Web Overview
◦ Bootloader Version is the version of the program that loads the operating system of the de- vice. • Network Information shows information about the wired network interface on the device. ◦ LAN: This will display the current MAC Address, and IP Address of the Ethernet interface. Wieland Electric GmbH | BA000870 | 06/2020 (Rev. A) -
Page 15: Wizard
EXIT button anytime. If the EXIT button is clicked, a pop-up window will be generated. The user will have a choice to either save or discard the settings which was made until that moment. Wieland Electric GmbH | BA000870 | 06/2020 (Rev. A) - Page 16 DNS IPs to enter here. Please consult your network administrator or internet service pro- vider (ISP) to obtain the local DNS's IP addresses. Click on NEXT to proceed to the next step. Wieland Electric GmbH | BA000870 | 06/2020 (Rev. A)
- Page 17 (network or COM), there will be one page for each COM within Step 5/6. wienet SDS series supports three different Link Modes which are TCP Server, TCP Client, and UDP. The Link Mode describes the role of wienet SDS and the connection between wienet SDS device and other remote devices in the network that would like to communicate with serial devices on wienet SDS's COM port(s).
- Page 18 When VirtualCOM is chosen in the application submenu, the serial device server will be seen as an extension of the COM peripherals on your computer. The user can click to download Wieland's wie- net Manager, a device management utility, and install Serial/IP utility from the provided link.
-
Page 19: Network Settings
Finally, the web browser will redirect you to the Overview page as shown in Figure 7. If you would like to discard any setting, please click the Cancel button. Wieland Electric GmbH | BA000870 | 06/2020 (Rev. A) -
Page 20: Serial
This section focuses only on the Serial Settings only. Figure 16 shows an example of the COM 1 Port Settings where the upper part is dedicated for Link Mode settings and the lower part is dedicated for Serial Settings. Figure 16: COM 1 Port Settings web page Wieland Electric GmbH | BA000870 | 06/2020 (Rev. A) -
Page 21: Com Configuration
Serial Settings page. If you want to cancel the change and reset all changes back to their original values, just click the Cancel button. The Advanced Settings button will be described in the next subsection. Wieland Electric GmbH | BA000870 | 06/2020 (Rev. A) -
Page 22: Com Configuration: Advanced Settings
• TCP Keep-alive: By clicking the Enable box of TCP Keep-alive and input value in seconds, wienet SDS will check if its peer is still alive. Noted that it will retry 3 times and timeout is 5 sec- onds in default. Wieland Electric GmbH | BA000870 | 06/2020 (Rev. A) - Page 23 Then, the Advanced Settings browser window can be closed by clicking on Close button and you will be returned to COM 1 Port Setting page. Wieland Electric GmbH | BA000870 | 06/2020 (Rev. A)
-
Page 24: Snmp/Alert Settings
The default wienet SDS's SNMP Commu- nity Strings (or passphrases) for Read Community and Write Community as shown in Figure 19 are public and private, respectively. Figure 20: SNMP Version v1/v2c/v3 is enabled Wieland Electric GmbH | BA000870 | 06/2020 (Rev. A) - Page 25 When the saving and applying are finished, the web browser will remain on the SNMP/Alert Settings page. If you want to cancel the change and reset all changes back to their original values, just click the Cancel button. Wieland Electric GmbH | BA000870 | 06/2020 (Rev. A)
-
Page 26: E-Mail Settings
SDS can lookup domain names and route the e-mails to the proper default gateway. Please see the Default Gateway and DNS Sever Settings in section 5.4 Network settings, p. 19. Wieland Electric GmbH | BA000870 | 06/2020 (Rev. A) -
Page 27: Log Settings
Log Settings page. If you want to cancel the change and reset all changes back to their original values, just click the Cancel button. Wieland Electric GmbH | BA000870 | 06/2020 (Rev. A) -
Page 28: Com Log Settings
COM Log Settings page. If you want to cancel the change and reset all changes back to their original values, just click the Cancel button. Wieland Electric GmbH | BA000870 | 06/2020 (Rev. A) -
Page 29: System Log
Moreover, you can choose from the drop-down list of 10 or 25 entries for the Show entries. Finally, you can search over the System Log by entering a keyword in the Search box. Wieland Electric GmbH | BA000870 | 06/2020 (Rev. A) -
Page 30: Com Log
Figure 27 lists the sub-menu under the System Setup. It consists of Date/Time Settings, Admin Settings, Firmware Upgrade, Backup/Restore Setting, and Ping. Each of this sub-menu will be described in the following subsections. Figure 27: System Setup menu Wieland Electric GmbH | BA000870 | 06/2020 (Rev. A) -
Page 31: Date/Time Settings
Date/Time Settings page. If you want to cancel the change and reset all changes back to their original values, just click the Cancel button. Wieland Electric GmbH | BA000870 | 06/2020 (Rev. A) -
Page 32: Admin Settings
5.9.3 Firmware upgrade Updated firmware for wienet SDS is provided by Wieland Electric from time to time to fix bugs and optimize performance. It is very important that the device must NOT be turned off or powered off during the firmware upgrade, (please be patient as this whole process might take up to 5 minutes). -
Page 33: Backup/Restore Configuration
Please contact Wieland authorized distributors for more information on this subject. To restore the backup configuration, click the Browse button under the Restore Configuration part as shown in Figure 31 to locate the backup configuration file on user's computer. -
Page 34: Ping
Figure 34. The device will then restart. When the rebooting process is finished, you will hear the beep sound twice from the device and you might need to refresh your web browser to log into the web interface of the device again. Figure 34: Reboot web page Wieland Electric GmbH | BA000870 | 06/2020 (Rev. A) -
Page 35: Specifications
3-Pin 5.08mm Lockable Terminal Block: 9–30 VDC DC Jack 5VDC Consumption Max. 1.5 W EMI/EMC FCC Part 15, Subpart B, Class A, EN 55032, EN 61000-3-2, EN 61000-3-3, EN 55024, EN61000-6-4, EN61000-6-2 Wieland Electric GmbH | BA000870 | 06/2020 (Rev. A) -
Page 36: Pin Assignments Of Serial Port
RS-422/RS 485 connector RS-232 RS-422/4-Wire RS-485 2-Wire RS-485 Pin no. Full Duplex Full Duplex Half Duplex TXD+ Data+ RXD+ SG (Signal Ground) SG (Signal Ground) SG (Signal Ground) RXD- TXD- Data- Wieland Electric GmbH | BA000870 | 06/2020 (Rev. A) -
Page 37: Led Indicators
Windows Virtual COM Driver and Linux TTY Driver: Linux 2.4.x, Linux 2.6.x, 3.x Utility • Web console • Serial console • SSH console Configuration Tool • Telnet console • wienet Manager Wieland Electric GmbH | BA000870 | 06/2020 (Rev. A) -
Page 38: Emergency System Recovery
*This firmware image can be obtained from Wieland's website. • If the device is beeping continuously after power up, this means that the bootloader is damaged and there is no way to recover it. Please contact Wieland directly to obtain RMA number for fur- ther solutions. -
Page 39: Service And Support
SERVICE AND SUPPORT Service hotline: +49 (0) 951 9324-995 E-mail: netcom@wieland-electric.com Wieland Electric GmbH Brennerstraße 10–14 D-96052 Bamberg Tel. 49 (0) 951 / 9324-0 49 (0) 951 / 9324-128 E-mail info@wieland-electric.com http://eshop.wieland-electric.com http://www.wieland-electric.com Wieland Electric GmbH | BA000870 | 06/2020 (Rev. A) -
Page 40: Appendix
Figure 31: Backup/Restore Settings web page under System Setup Figure 32: Ping web page under System Setup Figure 33: Unreachable ping example Figure 34: Reboot web page Figure 35: DB9 pin number Figure 36: TB5 pin number Wieland Electric GmbH | BA000870 | 06/2020 (Rev. A) -
Page 41: List Of Tables
Table 3: Security, Serial, and SNMP default settings Table 4: Hardware specification Table 5: Pin assignment for DB9 to RS-232/RS-422/RS-485 connector Table 6: Color interpretation of LED indicators Table 7: Software tools and utilities Wieland Electric GmbH | BA000870 | 06/2020 (Rev. A) - Page 42 Wieland Electric GmbH Brennerstraße 10 – 14 DE-96052 Bamberg Tel +49 951 9324-0 Fax +49 951 9324-198 info@wieland-electric.com www.wieland-electric.com...