Filling The Water Tank; Using The Steam Iron - Panasonic NI-GWF150 Operating Instructions Manual

9.  Press the telescopic button on the
back of the ironing board, and lift the
crossbar up until the telescopic poles
extend to the maximum height.
Note: When pressing the telescopic
button to adjust the height of
Telescopic button
the telescopic poles, make
sure that all the buckles are
locked.
 Place the iron head into the iron
holder.
 Clip the hose into the hose hook.
10. Before use, iron the ironing cloth by
referring to "Using the steam iron"
on page 13 to make it fit the ironing
board better (setting the function to
" ").
You can press the telescopic button on the
back of the ironing board to adjust the height
of the telescopic poles as needed (adjustable
in three height levels).
When the ironing board is used horizontally,
four height levels are available.
12

Filling the water tank

Be sure to disconnect the power plug from the outlet
before filling the water tank.
1. Remove the water tank by gently lifting its handle upward
from the side of the power base. Turn the water tank upside
down, and hold it bottom up.
2.  Open the water inlet cap on the bottom of the water tank.
 Put the water tank
under a faucet
stably and
2
fill it with a
proper amount
of water.
 Tighten the
water inlet
cap.
3. Attach the water tank back to the power base. Be sure to
fit them firmly.
 Insert the lower part of
the water tank into the
power base first.
 Push the upper part of
the water tank into the
power base until a "click"
is heard.
Notes:
a.The capacity of the water tank is about 1.6 L when water reaches
the lower part of the water inlet or when the water level window is
completely covered by water. Please fill the water tank with a
proper amount of water.
b.To prevent scale from accumulating in the product and thus affecting
its performance, we recommend using distilled water or pure water.
c.When you are filling the water tank, water may accumulate in the
groove for placing the water tank on the power base, which is not
a malfunction. Please clean any water in the groove before
installing the water tank back.
d.When installing the water tank, let the water inlet cap get in first,
and then install the whole water tank back. Do not apply too much
force during the assembly.

Using the steam iron

1. Insert the power plug into the household outlet.
2. Press the power button. The power indicator lights up,
and the " " indicator also starts flashing.
3. Wait until the " " indicator stays on after flashing
(for about 50 seconds), and then press the level switching
button to select the desired level.
Blue light
Red light Green light
While you are switching between levels, the function
indicators light up circularly.
It means that the level switches once each time you press
the level switching button. To switch to any other level, press
the level switching button multiple times until you get the
desired level. However, " " is not available to select
during the level switching. For details on how to use the
" " level, refer
to "Self-cleaning"
on page 16.
4. Iron the clothes.
It is recommended to put the iron head into the iron holder
when you sort out or change a garment. In this case, the
steam automatically stops, and you can resume using the
product by picking the iron head up again.
5. Press the power button to turn the product off when you have
finished, and then disconnect the power plug.
Notes:
a.The level mark is only visible when the power is on and the
setting is going on.
b.Do not place the iron head into the iron holder with the hose twisted.
c.If the water level in the water tank is lower than the bottom of the
water level window, please add water.
d.Do not remove the water tank from the power base during use.
e.You can turn the steam off by pressing the level switching button
to switch to the " " level or placing the iron head on the iron
holder, but the steam will keep coming out for a short time.
f.During ironing, there may be water dripping from the soleplate
surface onto the garment, which is not a malfunction.
g.Turn off the power button and disconnect the power plug before
taking out the water tank from the power base.
h.Do not perform the following operations during use. Otherwise
water may leak from the soleplate.
• Suddenly cut the power off or turn the power button off when
using the steam.
• Remove the water tank from the power base during use.
13