Related Manuals for Yamaha MY8-LAKE
Summary of Contents for Yamaha MY8-LAKE
- Page 1 Lake PROCESSING CARD Lake ® PROCESSING CARD ® MY 8 - LAKE MY 8 - LAKE Owner’s Manual Bedienungsanleitung Mode d’emploi Manual de instrucciones Manuale di istruzioni Руководство пользователя 取 扱説 明 書...
- Page 2 Compliance * This applies only to products distributed by YAMAHA CORPORATION OF AMERICA. (class B) COMPLIANCE INFORMATION STATEMENT (DECLARATION OF CONFORMITY PROCEDURE) Responsible Party : Yamaha Corporation of America Address : 6600 Orangethorpe Ave., Buena Park, Calif.
-
Page 3: Table Of Contents
Levels Screen ............16 PEQ & GEQ Overlays..........18 HPF/LPF Screen (Mesa mode only)......19 Storing Modules and Systems ........20 Changing the MY8-LAKE Frame Configuration ..21 XOVER Screen (Contour mode only) ......22 Contour Levels Screen..........22 Appendix ............24 Problems and Warnings.......... -
Page 4: Precautions
Yamaha cannot be held responsible for damage following: caused by improper use or modifications to the • Do not install the card in any Yamaha products not device, or data that is lost or destroyed. specified by Yamaha for use with the card to avoid possible electrical shock, fire, or equipment damage. -
Page 5: Introduction
RMS and peak Welcome limiters featuring Lake LimiterMax™ technology. Thank you for choosing the Yamaha MY8- ® LAKE Lake Processing card. The MY8- • Eight internal host inputs/outputs and LAKE is a DSP expansion Mini-YGDAI card eight AES inputs/outputs. -
Page 6: Usb Flash Drive Contents
To view PDF files, you will need to install Controller software (for Windows), which is Adobe Reader on your computer. You can necessary for use of the MY8-LAKE card, download the latest Adobe Reader at the along with the associated documentation following website: http://www.adobe.com... -
Page 7: Part Names And Functions
For additional information about LED indications and their meaning, refer to the section “Problems and Warnings” in the chapter “Appendix.” STATUS: • The green LED flashes to indicate that the MY8-LAKE card is correctly booted and operational; it is lit (static) when the digital input clock is locked. MY8-LAKE Owner’s Manual... -
Page 8: Configuration And Module
Configuration and Module Mesa Configuration Signal Flow (System EQ) The MY8-LAKE defaults to an 8x8 system EQ configuration referred to as Mesa mode. This configuration provides eight discrete channels of audio processing as shown in the diagram below. Module Input Section... -
Page 9: Contour Configuration Signal Flow (Crossover)
Contour Configuration Signal Flow (Crossover) In Contour mode (crossover), the MY8-LAKE provides 4x12 crossover modules as shown in the diagram below. Module Output Section Gain / Delay LimiterMax Polarity / Mute RMS/Peak Module Input Section Gain / Delay LimiterMax Polarity / Mute... -
Page 10: Contour/Mesa Configuration Signal Flow
“Mesa EQ.” In Contour mode the MY8-LAKE Frame contains up to four modules labeled A – D; in Contour/ Mesa mode there are up to six modules labeled A – F. The number of modules available in a Contour or Contour/Mesa mode is dependent on the Contour module types in use. -
Page 11: System Examples
System Examples The MY8-LAKE card can be used in a variety of ways; this chapter describes two typical scenarios. System EQ (Mesa) System EQ can be applied in Mesa mode; this is the default configuration for the MY8-LAKE card. Mesa mode provides eight channels of discrete audio processing that can be assigned to the host channel Insert Ins from the Insert Outs, without the use of any physical cabling—... -
Page 12: Quick Start Guide
On the INSERT screen of the the same network for the other Lake console, patch the corresponding channels devices, additional network of the SLOT for the MY8-LAKE card to the configuration will be required. Insert Outs and Ins of the desired channels •... -
Page 13: Starting The Lake Controller
For instructions on changing the To start the Lake Controller with an online configuration, refer to “Changing the MY8- MY8-LAKE card connected for the first time, LAKE Frame Configuration” on page 21. follow the steps below. Tap the [Modules] button from... -
Page 14: I/O Configuration
The existing data will be read from the summary text will open a pop-up hardware to synchronize the Controller screen with additional data; the right with the MY8-LAKE. The Frame is now side of the screen provides interactive online and ready for control and signal flow diagrams. - Page 15 Tap any of the magnifying glass icons on the far right of the screen. The Output Configuration screen will be displayed allowing you to route any MY8-LAKE Owner’s Manual...
-
Page 16: Levels Screen
Output Configuration screen. Check any associated mute and level settings in the MY8-LAKE NOTE You can also close the screen by host device. pressing <Esc>, then pressing <F1> to Assuming there is an audio signal return to the Home screen. - Page 17 Mode activation before the functions are Config screen is set to +24 dBu by displayed. For further information on default for the MY8-LAKE (which is the Designer Mode and more detailed Levels case for most of Yamaha consoles). screen functionality, refer to the Lake However, the limiter levels should be Controller Operation Manual.
-
Page 18: Peq & Geq Overlays
0 dB line side in the middle of the screen, and a graphical filter editing tool appears at the bottom of the screen. • The Mesa EQ filter is a unique filter that allows separate control of both MY8-LAKE Owner’s Manual... -
Page 19: Hpf/Lpf Screen (Mesa Mode Only)
EQ. Tap the [HPF Enable] and the Tap on the associated filter point [LPF Enable] buttons (so that ‘X’ to select a GEQ2 filter that they turn orange). overlaps the PEQ1 Mesa filter frequency range. MY8-LAKE Owner’s Manual... -
Page 20: Storing Modules And Systems
Tap the [HPF Select] button, then Module Store/Recall function is activated. select a desired type of filter from the scroll bar that appears. Tap the [New Store] button, then enter a module filename, and Scroll bar then tap [OK] (or press <Enter>). MY8-LAKE Owner’s Manual... -
Page 21: Changing The My8-Lake Frame Configuration
The default 4 x Classic 2-Way Crossover modules appear as shown below. Changing the MY8-LAKE Frame Configuration To review the functionality of the MY8-LAKE card in loudspeaker processor (Contour) mode, the MY8-LAKE Frame configuration must be changed from the default Mesa mode to Contour mode. -
Page 22: Xover Screen (Contour Mode Only)
The XOVER screen is available only on EQ changes on the XOVER screen only Contour modules when the MY8-LAKE card affect the selected channel, even if the is configured either in Contour mode or the slope of the EQ filter crosses the hybrid Contour/Mesa mode. - Page 23 (Low & High) to the right. • For additional information about the Lake Controller, including module grouping, XOVER and HPF/LPF ganging, Designer Mode functionality, and other advanced user options, refer to the Lake Controller Operation Manual. MY8-LAKE Owner’s Manual...
-
Page 24: Appendix
Appendix Problems and Warnings Problems, warnings, and other certain types of information are displayed via the MY8-LAKE panel indicators. Indicators Details Solution FAULT Flash No input source is available. Refer to “No Sound” in the “Troubleshooting” section. The digital clock is slipping. -
Page 25: Troubleshooting
AES output on the screen? Output Configuration screen on the Lake Controller. Are all mute points in the MY8-LAKE signal Check that all Input Router, module Input and module path unmuted? Output Mutes are properly unmuted. - Page 26 IP address, such as 192.168.0.x. Are any Dante-enabled devices present Additional network hardware configuration may be on the network? required; refer to the Lake Network Configuration Guide. * If any specific problem should persist, please contact your Yamaha dealer. MY8-LAKE Owner’s Manual...
-
Page 27: Specifications
Terminal name Format Data Sampling Level Connector length Frequency AES/EBU AES/EBU 24 bit 44.1 kHz, 48 kHz, RS422 D-sub 25 pin (In/Out Ch 1-8) 88.2 kHz, 96 kHz (I/O individually selectable per Ch) NETWORK 10Base-T/ RJ-45 (Ethernet) 100Base-T MY8-LAKE Owner’s Manual... - Page 28 * Specifications and descriptions in this owner’s manual are for information purposes only. Yamaha Corp. reserves the right to change or modify products or specifications at any time without prior notice. Since specifications, equipment or options may not be the same in every locale, please check with your Yamaha dealer.
- Page 29 Yamaha. * Le specifiche e le descrizioni presenti in questo manuale sono fornite a fini puramente informativi. Yamaha Corp. si riserva il diritto di modificare prodotti o specifiche in qualsiasi momento senza preavviso. Dato che le specifiche, le apparecchiature o le opzioni possono essere diverse da paese a paese, verificarle con il proprio rappresentante Yamaha.
- Page 30 Information for Users on Collection and Disposal of Old Equipment This symbol on the products, packaging, and/or accompanying documents means that used electrical and electronic products should not be mixed with general household waste. For proper treatment, recovery and recycling of old products, please take them to applicable collection points, in accordance with your national legislation and the Directives 2002/96/EC.
- Page 33 Yamaha Pro Audio global web site http://www.yamahaproaudio.com/ Yamaha Manual Library http://www.yamaha.co.jp/manual/ C.S.G., Pro Audio Division © 2011 Yamaha Corporation 112MW-A0...