Download Print this page

Advertisement

Quick Links

PAT 4.0 AUTOMATIC CABLE TIE INSTALLATION SYSTEM
© Panduit Corp. 2017
PAT 4.0 FAMILY TOOLS: Automatic Cable Tie Installation Tools
PDM4.0 Data Manager Operations Manual (PA25060A01)
EI I/O port (25 Pin Connector) is internally connected
• TO REDUCE THE RISK OF INJURY,
Email:
techsupport@panduit.com
EU Website:
www.panduit.com/emea
EU Email: emeatoolservicecenter
@panduit.com
PDM4.0 EI Setup
ELECTRONIC INTERFACE USER MANUAL
EI (Electronic Interface) Instructions
For use with the following Systems &
respective Operational Manuals:
PDM4.0: Dispenser
PHM: Feeder Hoses
Operation Manual (PA27647A01)
to Optically Isolated Modules,
WARNING
USER MUST READ INSTRUCTION
MANUAL
www.panduit.com
Original Instructions
Panduit Corp. • Tinley Park, IL USA
Technical Support
Tel: 1-800-777-3300
Panduit Europe • EMEA Service Center
Almelo, Netherlands
Tel: +31 546 580 452 • Fax: +31 546 580 441
PA28091A01
Rev. 02 2-2017

Advertisement

loading

Summary of Contents for Panduit PDM4.0 EI

  • Page 1 EI I/O port (25 Pin Connector) is internally connected to Optically Isolated Modules, WARNING • TO REDUCE THE RISK OF INJURY, USER MUST READ INSTRUCTION MANUAL Email: Panduit Corp. • Tinley Park, IL USA techsupport@panduit.com Technical Support Tel: 1-800-777-3300 EU Website: www.panduit.com/emea Panduit Europe • EMEA Service Center www.panduit.com...
  • Page 2: System Specifications

    © Panduit Corp. 2017 1: INTRODUCTION The PAT Fully Automatic Cable Tie Installation System was designed by Panduit Corporation to install Panduit continuously molded cable ties for high volume wire harnessing applications. NOTE: In the interest of higher quality and value, Panduit products are continually being improved and updated.
  • Page 3 ELECTRONIC INTERFACE USER MANUAL © Panduit Corp. 2017 Automatic Cable Tie Tool System Overview & Tool Cycle: (Applies to all Panduit Automatic Cable Tie Tool Systems, Listed on Page 1) Tool Cycle with Customer Controlled Tool Actuator / Robot & Use of EI-Port: Customer Controlled Actuator closes Tool Head Jaw lever, closing Jaw &...
  • Page 4 PAT 4.0 AUTOMATIC CABLE TIE INSTALLATION SYSTEM ELECTRONIC INTERFACE USER MANUAL © Panduit Corp. 2017 EI I/O Port Modules: Electrical Specification / Schematic Input/Output PDM Input PLC PNP Sourcing Output Isolation 3500V Output EI Connector 24VDC at rear of Panduit...
  • Page 5 PAT 4.0 AUTOMATIC CABLE TIE INSTALLATION SYSTEM ELECTRONIC INTERFACE USER MANUAL © Panduit Corp. 2017 I/O Port: Pin-Out (see functions, page 5) 12 VDC Output (+) 12 VDC Output (+) Remote Operation Enable: M0 Input (+) M0 Input (-): Remote Operation Enable...
  • Page 6 PAT 4.0 AUTOMATIC CABLE TIE INSTALLATION SYSTEM ELECTRONIC INTERFACE USER MANUAL © Panduit Corp. 2017 I/O Port Functions (“M#” indicates I/O Module #) 25 PIN D-SUB Pin Numbers NUMBER IO Function Definition 12 VDC Output @ 0.75 A 1,14 Chassis Ground...
  • Page 7 PAT 4.0 AUTOMATIC CABLE TIE INSTALLATION SYSTEM ELECTRONIC INTERFACE USER MANUAL © Panduit Corp. 2017 Cycle Progress Signal Definition (“M#” indicates I/O Module #) (See Flow Chart on pages 6 & 7 for cycle timing) INPUTS OUTPUTS Cycle Trigger Reset...
  • Page 8 PAT 4.0 AUTOMATIC CABLE TIE INSTALLATION SYSTEM ELECTRONIC INTERFACE USER MANUAL © Panduit Corp. 2017 EI PLC Program Flow Chart Recommendation Notes: 1. Input “Off or Open” = Applies voltage less than minimum drop-out level. Start PLC 2. Input “On or Closed” = Applies voltage within specified input range.
  • Page 9 PAT 4.0 AUTOMATIC CABLE TIE INSTALLATION SYSTEM ELECTRONIC INTERFACE USER MANUAL © Panduit Corp. 2017 Cable Tie Dispenser Display for Errors & Corrective Action Dispenser Possible Cause Corrective Action Display “Dispenser jam - Dispenser rotary receiver Press "Buzzer" button to turn buzzer off.
  • Page 10 PAT 4.0 AUTOMATIC CABLE TIE INSTALLATION SYSTEM ELECTRONIC INTERFACE USER MANUAL © Panduit Corp. 2017 Cable Tie Dispenser Display for Errors & Corrective Action (Continued) Dispenser Possible Cause Corrective Action Display “Blocked or dirty Tool sensor is obstructed 1. Press "Buzzer" button to turn buzzer off'.