Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Related Manuals for Eastwood 51088
Summary of Contents for Eastwood 51088
- Page 1 Item #51088 SHRINKER STRETCHER COMBO SET INSTRUCTIONS...
-
Page 2: Specifications
The EASTWOOD SHRINKER/STRETCHER METAL-SHAPING COMBO SET allows easy fabrication of many auto body sections including window reveal openings, wheel well lips, dog legs, trunk corners, headlamp flanges, body bracing...almost any metal fabrication requiring a combination curve and angle. Use the shrinker to contract metal for inside curves; use the stretcher to expand metal for outside curves. -
Page 3: Safety Information
DO NOT add pipe, bars or any other devices which would add additional length to the Handle to increase bending force. This will exceed the design limits of the tool and can result in serious injury and/or component failure. To order parts and supplies: 800.343.9353 >> eastwood.com... -
Page 4: Cut Hazard
Before beginning ANY work with this tool, it is absolutely necessary that it be securely bolted to a solid, level, well supported surface capable of withstanding the tremendous torque and side loads this tool is subjected to during use. Eastwood Technical Assistance: 800.343.9353 >> techelp@eastwood.com... - Page 5 " " " " • Use (2) 3/8-16 x 1” bolts (not FIG. 3 included) and washers to secure base to an optional #20357 Base Plate for vise mounting or drilled work surface (Fig 3). To order parts and supplies: 800.343.9353 >> eastwood.com...
- Page 6 Fulcrum Lever so that the an- nular groove is positioned under the Set Screw (FIG 4). • Using a 3mm Hex Key (not FIG. 4 included), tighten Set Screw in Fulcrum Lever to retain Handle (FIG 5). FIG. 5 Eastwood Technical Assistance: 800.343.9353 >> techelp@eastwood.com...
- Page 7 Wire Bail off the Actuating Bar (FIG 7). ATTACHING JAWS • Slide Jaws onto Body with screw slots located under Thumb Screws. • Place Wire Bail over top of Actuating Bar. • Tighten Jaw Thumb Screws. To order parts and supplies: 800.343.9353 >> eastwood.com...
-
Page 8: Operation
This will exceed the design limits of the tool and can result in severe injury and/or component failure. Workpiece material should be clean of any rust, burrs, nicks, welds or coat- ings before attempting to bend or interference and binding may occur. Eastwood Technical Assistance: 800.343.9353 >> techelp@eastwood.com... - Page 9 Jaws along its entire planned length so that each area is exposed to the Jaws numerous times rather than trying to shrink or stretch “all in one bite”. To order parts and supplies: 800.343.9353 >> eastwood.com...
- Page 10 Stretcher on scrap material is highly recommended. As with many metal working tools, a period of “trial and error” is needed to achieve a degree of proficiency in their use. Remember, a little time and material wasted at this step will avoid disappointing results on an actual project. Eastwood Technical Assistance: 800.343.9353 >> techelp@eastwood.com...
-
Page 11: Maintenance
• Check tightness of all hardware. • Check operation for binding. Lubricate sliding parts and pivot points periodically with medium bodied oil. Use care to avoid getting oil on Jaw Gripping Teeth which will reduce their grip. To order parts and supplies: 800.343.9353 >> eastwood.com... -
Page 12: Additional Items
Bead Roller If you have any questions about the use of this product, please contact The Eastwood Technical Assistance Service Department: 800.343.9353 >> email: techelp@eastwood.com PDF version of this manual is available at eastwood.com The Eastwood Company 263 Shoemaker Road, Pottstown, PA 19464, USA 800.343.9353 eastwood.com...