Table Of Contents - HP 8340A Operating Manual

Model 8340A
Section
I GENERAL INFORMATION
1-1. Introduction
1-7. Specifications
1-9. Safety Considerations ............. 1-2
1-11. Instruments Covered by Manual .... 1-2
1-16. Description ..................... 1-3
1-25. Options ........................ 1-3
1-26. Option 001, Front Panel RF Output,
No Attenuator .............. 1-3
1-28. Option 004, Rear Panel RF Output
with 90 dB Attenuator ........ 1-3
1-30. Option 005, Rear Panel RF
OUTPUT with No Attenuator . 1-3
1-32.
Option 006, Delete Pulse
Modulation
1-33. Option 007, Relaxed Phase Noise
Specifications ............... 1-3
1-34. Option 806, Chassis Mount
Slide Kit ................... 1-3
1-36. Option 850, Model 8410B/C
Interface
Cable
1-38.
Option 908, Rack Flanges without
Handles Kit
1-40.
Option 910, Extra Manual Set .... 1-4
1-42. Option 913, Rack Flanges with
Handles Kit
1-44. Option 914, Delete Service
Documentation ............. 1-4
1-46. Equipment Required But
Not Supplied
1-49. Equipment Available ............. 1-4
1-50. Service Accessories
1-52. Model 8410C/8411A Network
Analyzer ................... 1-4
1-54. HP Model 8755 Frequency
Response Test Set
1-57.
HP Model 8756A Scalar Network
Analyzer ................... 1-5
1-59. Power Meters and Crystal
Detectors
1-61. Recommended Test Equipment
II
INSTALLATION
2-3. Initial Inspection
2-5. Preparation For Use .............. 2-1
2-6. Power Requirements ........... 2-1
2-8. Line Voltage and Fuse Selection .. 2-1
2-10. Power Cable .................. 2-1
2-13. HP-IB Address Selection ........ 2-2
2-15. Interface Function Codes
2-17.
Mating Connectors
VOLUME 1_ CONTENTS
Page
........... 1-1
.................... 1-1
................... 1-2
................ 1-3
..................... 1-4
................ 1-4
.................. 1-4
............... 1-4
............ 1-4
........... 1-5
.................. 1-5
.... 1-5
..................... 2-1
... ............ 2-1
_
....... 2-4
............ 2-4
Scans by HB9HCA and HB9FSX
Section
2-19. HP-IB, 8410, and 8755 Interface
Connectors
Internal Oscillator Selection and
2-21.
Warmup Time .............. 2-4
Operating Environment
2-24.
Temperature
2-25.
2-26. Humidity .................... 2-4
2-27. Altitude
2-28. Cooling ...................... 2-8
2-29. Front Handles Kit ............. 2-8
2-31. Chassis Slide Kit (Option 806) ... 2-8
2-33. Rack Flange Kit (Option 908) .... 2-8
Rack Mounting with Handles
2-35.
(Option 913)
2-37. Storage and Shipment
2-38. Environment ..
2-41. Packaging .................... 2-9
2-42. Original Packaging ............. 2-9
2-43. Other Packaging ............... 2-9
2-44. Blue Service Tags .............. 2-9
"incoming Inspection
2-46.
Procedure
III OPERATING INFORMATION
Introduction ........
LOCAL OPERATING INFORMATION
Power dBm display .................... 3-7
START/CW/CF Frequency Display
STOP/L'.lF Frequency Display ........... 3-10
Entry Display ........................ 3-11
Function ............................ 3-13
KNOB/STEP Entry ................... 3-16
Frequency Marker .................... 3-17
Entry .............................. 3-20
Sweep and Trigger .................... 3-22
Instrument State ..................... 3-25
Power Switch, Sweep Output ........... 3-27
Modulation ......................... 3-28
Modulation Input ......
Leveling ............................ 3-30
RF Output .......................... 3-32
Rear Panel BNC Connectors
Rear Panel RF Output
HP-IB Connector .................... 3-38
HP 8410 Interface .................... 3-40
HP 8755C Interface ................... 3-42
Fan Assembly ....................... 3-43
Power Line Module
HP-IB PROGRAMMING
INFORMATION .................. 3-45
Introduction ......

Table of Contents

Page
................ 2-4
........ 2-4
................. 2-4
..................... 2-4
............... 2-9
............ 2-9
.............. 2-9
_
................. 2-9
................. 3-1
_
...... 3-9
............. 3-29
.
........... 3-35
................ 3-37
.......... ....... 3-44
.
................. 3-45
.