Advertisement
Quick Links
©2019 Growers Supply
All Rights Reserved. Reproduction
is prohibited without permission.
Revision date: 01.03.19
GROWSPAN
Round Pro Greenhouses and Systems
Photo may show a different but similar model.
ROUND PRO GREENHOUSES AND SYSTEMS
™
GrowSpan
™
STK#
104861
104862
104863
104864
DIMENSIONS
38' W x 15' H x 40' L
38' W x 15' H x 48' L
38' W x 15' H x 72' L
38' W x 15' H x 96' L
1
Advertisement
Related Manuals for FarmTek Growers Supply GrowSpan Round Pro
Summary of Contents for FarmTek Growers Supply GrowSpan Round Pro
- Page 1 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ GrowSpan ™ Round Pro Greenhouses and Systems Photo may show a different but similar model. STK# DIMENSIONS 104861 38' W x 15' H x 40' L 104862 38' W x 15' H x 48' L 104863 38' W x 15' H x 72' L ©2019 Growers Supply...
- Page 2 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ LOCATION Choosing the proper location is an important step before you begin to assemble the structure. The following suggestions and precautions will help you determine whether your selected location is the best location. YOU MUST READ THIS DOCUMENT BEFORE YOU •...
-
Page 3: Assembly Procedure
GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ ASSEMBLY PROCEDURE • Band Clamp: Clamp used to connect the end wall framing to the rafter pipe. In some cases, band Following the instructions as presented will help ensure clamps are also used to connect diagonal struts to the the proper assembly of your greenhouse. - Page 4 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ REQUIRED TOOLS SPECIAL NOTE: Baseboards for Frame The following list identifies the main tools needed to These instructions recommend installing a baseboard assemble the shelter. Additional tools and supports may be under the mounting feet along each side of the frame. The needed depending on the structure, location, and baseboard runs from the front to the back of the building.
- Page 5 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ The following graphics and photos will help you identify the different parts and show you how they are used. (Some parts are not shown.) QH1070 FA4482B CC6212 102717 103544 102546 102569 Tek Screw Gearbox Drive Pipe Strap Fabric Clip...
- Page 6 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ H-CHANNEL INSTALLATION INSTRUCTIONS The new H-channel design requires installation of the flat side facing out with channel side toward the building. Some diagrams and photos in this document show installation of original H-channel with channel side facing out.
- Page 7 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ GrowSpan ™ Round Pro Greenhouses and Systems The instructions that follow describe assembling all rafters and then constructing the frame. Depending on the number OVERVIEW of individuals assisting with the construction, it may be best This section describes assembling your Round Pro and more efficient to have someone assemble the rafters Greenhouse.
- Page 8 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ LAY OUT THE BUILDING SITE NOTE: Setting customer-supplied baseboards on the site in the correct positions is another way to prepare After the site is prepared, identify the location of the shelter for the frame assembly. corners helps to square the frame after it is assembled.
- Page 9 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ ASSEMBLE THE GREENHOUSE COMPONENTS NOTE: Assistance is required to assemble the shelter. END RAFTER ASSEMBLY (2) ATTENTION: After assembling the end rafters, set the two (2) identical rafters aside in an accessible place. Gather the parts: One rafter is used at each end of the frame during the •...
- Page 10 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ INTERIOR RAFTER ASSEMBLIES Gather the parts: • Rafter pipe (#37R23S1D) • Rafter pipe (#38R23S1) • Rafter pipe (#38R23P2) • Rafter foot (#104302) • Tek screws (#FA4482B) • FAG363B 3/8" x 3" bolt and FALB04B 3/8" nut Assemble Interior Rafters With Attached Ratchets 1.
-
Page 11: Frame Assembly
GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ FRAME ASSEMBLY 3. Secure the rafter feet to the site (or customer-supplied baseboards) to prevent the rafter from shifting. Gather the parts: • All rafter assemblies • Purlin pipe 1.315" x 75" swaged (131S075) •... - Page 12 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ FRAME ASSEMBLY (CONTINUED) 11. Move to the other side of the rafter and repeat Step 10. 5. Place a cross connector at the top of the inside rafter, 12. Install the first pipe section of remaining purlins. (There align it with the QH1070 pipe strap attached to the end are eleven (11) purlins between each rafter.) Consult rafter in the same location, and insert the plain end of...
-
Page 13: Cable Assembly
GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ CABLE ASSEMBLY Cable assemblies provide diagonal bracing for the building. Each cable assembly includes the following items: • Cable (2 cables cut to length) ATTENTION: Consult the diagram on the next page to •... - Page 14 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ CABLE ASSEMBLY (CONTINUED) 5. Install a second cable clamp on the cable six to eight (6"-8") inches from the first clamp and tighten both clamps. 6. Remove the bolt from the jaw of the turnbuckle and position the cable end with the thimble into the turnbuckle jaw. 7.
-
Page 15: Cable Placement
GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ CABLE PLACEMENT The diagram and inserts below identify the placement and 5" Carriage Bolt proper way to attach the cable assemblies to the building. ATTENTION: Install a carriage bolt in this Do not tighten the cables until the frame is properly and location at both ends of securely anchored to the site as described in the Must the shelter. - Page 16 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ ANCHOR THE SHELTER FINAL FRAME CHECK After installing all cable assemblies, anchor the frame. 1. Return to the frame connections and verify that all bolts Once the frame is anchored properly, continue with these are tight.
- Page 17 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ END WALL INSTALLATION • DO NOT REPOSITION THE END WALL VERTICALS USED AT THE SEAM OF TWO (2) POLYCARBONATE The steps to install the end walls for the greenhouse PANELS. include the following: •...
- Page 18 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ END WALL INSTALLATION (continued) 9. Measure the distance between the top of the base tube 4. Secure the base tube between the legs of the end and band clamp (Step 7) to determine the length of the rafter using an angle bracket and Tek screws.
- Page 19 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ INSTALL THE END WALL FRAME (continued) 17. Using a level (or other means), verify that one vertical door frame tube is plumb and tighten the band clamp 15. Using the marks on the base tube for the rough bolt to lock the first door frame member in place.
- Page 20 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ INSTALL THE END WALL FRAME (continued) 27. With the square-to-round tube connect bracket attached to the top of the frame member, place a 22. Use the end frame diagram to determine the number of square tube fitting on the bottom of the frame member.
- Page 21 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ INSTALL THE END WALL FRAME (continued) TAPE SHARP EDGES AND CONNECTORS After the frame is assembled, check the frame for sharp INSTALL BACK END WALL FRAME (NO DOOR) edges that could damage the cover or end panel, and file these smooth or tape over them using the supplied duct End wall framing for back of greenhouse is assembled in tape.
- Page 22 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ END PANEL INSTALLATION Secure all polycarbonate panels as shown in the diagrams and photos below, unless otherwise noted. After end wall framing is installed, attach polycarbonate panels to end wall framing. Steps that follow describe one way to complete panel installation.
- Page 23 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ END PANEL INSTALLATION (continued) 5. Place panel in position, attach it to end wall framing Complete the following general steps to install end wall using FA4484B Tek screws and 102921B washers. panels. H-channel here – outer 1.
- Page 24 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ END PANEL INSTALLATION (continued) 9. After cutting panels, attach 104213 profile to upper (or outer) edge of all panels. See dashed line in diagram 7. Continue to prepare and install panels and aluminum under previous step for profile location.
- Page 25 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ 5. Measure, cut and install U-channel profile (104213) to DOUBLE DOOR ASSEMBLY all edges of the panel. The materials and parts needed to assemble the doors include: Photo shows panel attached to the outside of the door frame and finished with U-channel.
- Page 26 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ DOUBLE DOOR ASSEMBLY (continued) a. Photo shows end cap as attached to door frame tube. View shows assembly from the outside. 8. Next, with assistance, lift door and attach to end wall frame using the long Tek screws. b.
- Page 27 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ DOUBLE DOOR ASSEMBLY (continued) INSTALL POLY LATCH U-CHANNEL 11. Next, install another section of end cap on the inside The double poly latch U-Channel (#104211) is attached to frame of the door that includes the chain latch. each side of the frame and runs from the front to the back of the shelter.
- Page 28 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ INSTALL POLY LATCH U-CHANNEL (continued) 8. After attaching the double poly latch to the sides of the frame, measure between the two runs of double poly 4. To begin, cut one 8' section of double poly latch latch channel at one end rafter to determine the length channel to 6' and attach the 6' section to the rafters of the single U-Channel.
- Page 29 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ INSTALL MAIN COVER (continued) 3. After tying the ropes to the main cover, throw the ropes over the top of the greenhouse and pull the covers into The steps that follow describe one way to complete this place.
- Page 30 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ INSTALL MAIN COVER (continued) Install the Inflation Fan Kit before installing the second main cover. Consult the instructions included with the 6. As the spring is install the spring into the U-channel Inflation Fan Kit to install the kit. Actual components at the top of the first end rafter, ensure that an even may differ from example shown.
- Page 31 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ INSTALL ROLL-UP PANELS ASSEMBLE THE ROLL-UP SIDE CONDUIT To this point, the main cover should be secured to Gather the Parts: the greenhouse and the roll-up side panels should be • Pipe 1.315'' x 75'' swaged 17 GA (#131S0075) positioned along the sides at the base of the frame.
- Page 32 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ ATTACH CONDUIT TO THE ROLL-UP SIDES TWIST-OF-THE-WRIST ASSEMBLY Gather the parts: Gather the parts: • Assembled conduits • Aluminum channel • Fabric clips #CC6212 (Divide quantity in half.) • Drive handle • Tek screws (#FA4482B) •...
- Page 33 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ TWIST-OF-THE-WRIST ASSEMBLY (continued) 6. Select the bearing bracket and attach the bearings as needed. (In some instances, the bearings may come 3. Select the aluminum channel and drill a 3/8" hole already attached.) Assemble as follows: through the channel approximately 2"...
- Page 34 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ TWIST-OF-THE-WRIST ASSEMBLY (continued) 15. Attach the rolled conduit to the square shaft of the assembly by inserting a carriage bolt through the hole 11. Using a carriage bolt, attach the square shaft to a in the conduit and tubing adapter.
- Page 35 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ INSTALL ANTI-BILLOW ROPES (continued) 6. Cut the rope and tie one end to the eyebolt. ATTENTION: If no wood baseboard is present as 7. Pull the rope tight and tie the remaining end to secure. required, additional steps must be take to anchor the lower portion of the anti-billow ropes.
- Page 36 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ SHELTER CARE AND MAINTENANCE Proper care and maintenance of the shelter is important. Space below is reserved for customer notes. Check the following items periodically to properly maintain the shelter: • Regularly check the cover or covers to see that these are tight and in proper repair.
- Page 37 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ Space below is reserved for customer notes. Revision date: 01.03.19...
- Page 38 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ 14'-10 1/2" Height QUICK START GUIDE 38'-0" Width 38' Round Pro Greenhouse FRONT Grid Represents 12" Squares Ground Level Frame shown may differ in length from actual frame. Revision date: 01.03.19...
- Page 39 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ Revision date: 01.03.19...
- Page 40 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ Revision date: 01.03.19...
- Page 41 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ Revision date: 01.03.19...
- Page 42 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ Revision date: 01.03.19...
- Page 43 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ Revision date: 01.03.19...
- Page 44 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ Revision date: 01.03.19...
- Page 45 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ Revision date: 01.03.19...
- Page 46 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ Revision date: 01.03.19...
- Page 47 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ Revision date: 01.03.19...
- Page 48 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ Revision date: 01.03.19...
- Page 49 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ Revision date: 01.03.19...
- Page 50 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ Revision date: 01.03.19...
- Page 51 GROWSPAN ROUND PRO GREENHOUSES AND SYSTEMS ™ Space below is reserved for customer notes. Revision date: 01.03.19...