Cleaning And Maintenance Instructions; Information For Test Laboratories; Troubleshooting - Brandt DWE 500 Operating Instructions Manual

Cleaning and maintenance instructions

• Your dishwasher comes with a self-cleaning
pulse filter that constantly filters small
particles of dirt trapped in the washing bath.
The filter and the main filter cannot be
dismantled as the cleaning arm constantly
cleans them.
Regularly clean the waste trap (Fig. 14). Pull
the handle, remove the residue with a brush
and clean with tap water. Put back in to its
housing making sure you clip it down
properly.
Clean as necessary
• Underneath the filters, around the door and
the door joint with a damp sponge to remove
any deposit.
• Use only soap and water for the bodywork
and control board.

Information for test laboratories

Capacity : 14 place setting :
Comparative tests according to : Fig. 10-11-13
with the drying button condensor activated, upper basket : setting the hight position.
IEC 436, DIN 44990 :
Programme 3 "Intensive Wash 70 °C "
EN 50242 :
Program 2 "Organic Wash 55 °C "
• It is essential that the softener be adjusted to a setting immediately above the recommended one,
according to the hardness of your water, to take into account the lack of phosphate in the
standardised detergent.
• Rinsing product set at : 2
• Quantity of washing product : 35 g. product B
24
Do not clean with abrasive powders,
scouring pads, spirit-based products or
solvent.
Use preferably a cloth or a sponge.
• If you have stainless steel door you may use
products adapted for stainless steel. See the
manufacturer's instructions for advice on their
use.
Every year
To maintain your machine in perfect working
order you should clean it once or twice a year.
Run an intensive programme with the machine
empty and a special dishwasher cleaning
product available from any reputable dealer.
Prolonged period of non-use
Clean your machine completely then unplug
the electricity supply and close the water tap.
Keep the appliance at a temperature above
freezing.
GB

Troubleshooting

Problems
The dishwasher will not start
The dishes are not properly washed (or
their are stains in it)
Greasy stains
Limescale deposits on the dishes
The dishes are dull
Traces of salt (salty taste on the dishes)
Blackened or marked silverware
Traces of rust on knife blades
The dishwasher does not empty
If you have problems not covered by these
remarks, consult your dealer or After-Sales
Service. Have the machine type, series
number or that mentioned on the rating plate
(inside the door) ready.
You will so avoid unnecessary delays and
cost.
Causes
- Is it plugged in ?
- Is the door properly closed ?
- Is the water connected ?
- Check that the "delayed start" is on "0" (according to the model)
- Programme choice. Choose the programme best adapted to the
type of wash
- Make sure nothing is blocking the circulation of the water
- Check the dishes are properly arranged.
- Only use specially designed washing products
- Check the waste well, filters, arms, joints and door rim are clean
- Clean the filter
- Check that the washing arm can freely rotate
- Increase the dose of washing product
- Use a new packet of washing product
- Choose a better adapted programme
Check it is limescale (clean with vinegar). If yes :
- Check the hardness of the water
Too soft water is aggressive for glasses.
- Check the hardness of the water
- Reduce the softener and if necessary remove the regenerating
salt.
- Add water to the salt pot and reload if necessary.
- Cap badly closed.
- Remove food residue immediately after use
- Separate silverware from other metals
- Choose detergent recommended for silverware
- Use knives suitable for dishwashers
- Remove the siphon stop valve
- Check the drain pipe is not bent or crushed
- You have moved your dishwasher and have tipped it backwards. To
restart the pump, unhook the draining rod, lay it on the floor at the
end of a basin, draining should restart. Then turn off the "Start/Stop"
button, put the draining rod back and restart your programme.
This machine complies with all applicable safety standards. Any
repairs should be carried out by a qualified technician. Repairs
carried out by unqualified technicians may be dangerous for the user.
GB
25