Notes On Usage; Unpacking And Checking The Delivery; Country-Specific Information - Siemens SIMATIC Field PG M5 Manual

Intense high frequency radiation
NOTICE
Observe immunity to high frequency radiation
The device has an increased resistance to high frequency radiation according
to the information on electromagnetic compatibility in the technical
specifications.
Radiation exposure to immunity levels above the specified limits can impair
device functions, result in malfunctions and cause harm to persons and
machines.
Observe the information on immunity to high frequency radiation in the
technical specifications.
CAUTION
Risk of interference with pacemakers
The radio waves of WLAN and Bluetooth may interfere with pacemakers.
If you wear a pacemaker, keep a minimum distance of 20 cm from the Field
PG when WLAN or Bluetooth is activated.
Danger of explosion
The radio waves transmitted by WLAN and Bluetooth may trigger an explosion
or fire.
Switch off WLAN and Bluetooth of the Field PG if you go in the vicinity of
flammable gases or in an explosive environment (e.g. paint shop).
Note
Remedy for faults in mouse cursor movement
In the case of cable-conducted interferences induced by high-frequency fields in
accordance with IEC/EN 61000-4-6, operation of the clickpad is only guaranteed
up to 3 V. If you detect faults in mouse cursor movement during operation in an
environment with interference and need to continue operation in this
environment, the following measures may help:
Establish an additional ground connection, for example via a shielded signal
•
cable.
Use a USB mouse and switch off the internal touchpad (hotkey Fn + F4).
•
In unfavorable conditions, static discharge (ESD acc. to IEC/EN 61000-4-6) can
•
cause the clickpad to fail. If a fault has caused the clickpad to fail, you can
reactivate it by pressing the hotkey Fn + F4 twice.
Limitations for operation of the Profibus/MPI interface
Activating the Profibus/MPI interface has the result that the emission
standard for residential areas (EN 61000-6-3) is not complied with. If you
notice interference from other devices when using the device in an office
environment, either establish a greater distance or deactivate the
Profibus/MPI interface.

Notes on usage

NOTICE
Ambient conditions and chemical resistance
Unsuitable environmental conditions have a negative impact on device
operation. Chemical substances, such as cleaners or fuels, can change the
color, shape and structure of the device surface.
The device may be damaged, possibly resulting in malfunctions.
For this reason, please observe the following precautions:
Always operate the device in closed rooms. All warranties shall be void in the
•
case of noncompliance.
Operate the device only in accordance with the ambient conditions specified in
•
the technical specifications.
Protect the device against dust, moisture and heat.
•
Do not expose the device to direct sunlight or to other strong sources of light.
•
Without additional safety measures, such as a supply of clean air, the device
•
may not be used in locations with harsh operating conditions caused by acidic
vapors or gases.
Always use suitable cleaning agents. Observe the notes regarding chemical
•
resistance that is available on the Internet (see operating instructions, "Service
and Support" pages, After Sales Information System SIMATIC PC/PGPC/PG).
WARNING
Risk of fire
The outer housing is made of magnesium. If it comes into contact with open
flame, there is a risk of fire / spreading fire.
4
Certificates and approvals
The certificates can be found on the device and on the Internet under:
Technical Support (https://support.industry.siemens.com).
Software license
For information regarding the Windows license, refer to the COA label on
the device. Observe the corresponding license agreements.

Unpacking and checking the delivery

1. When accepting a delivery, please check the packaging and the
contents for visible transport damage.
2. If any transport damage is present at the time of delivery, lodge a
complaint at the shipping company in charge. Have the shipper
confirm the transport damage immediately.
3. Keep the original packaging in case you have to transport the unit
again.
4. If the contents of the packaging are incomplete, damaged or do not
match your order, inform the responsible delivery service
immediately. Fax the enclosed form "SIMATIC IPC/PG Quality
Control Report".
WARNING
Electric shock and fire hazard due to damaged device
A damaged device can be under hazardous voltage and trigger a fire in
the machine or plant. A damaged device has unpredictable properties and
states. This can result in personal injuries or material damage.
Make sure that the damaged device is not inadvertently installed and put
into operation. Label the damaged device and keep it locked away. Send
off the device for immediate repair.
5. When storing the device, please note:
– Store the device in a dry place.
– Bring the device to room temperature before commissioning.
– Do not expose the device to direct heat radiation from a heating
device.
– If condensation develops, wait approximately 12 hours or until the
device is completely dry before switching it on.
6. Please keep the enclosed documentation in a safe place. It belongs
to the device. You need the documentation when you commission the
device for the first time.
7. Write down the identification data of the device.

Country-specific information

WARNING
Operation only in grounded power supply systems
The device is designed only to be used in grounded power supply systems
(TN systems to VDE 0100, part 100, or IEC 60364-1). It must not be used in
ungrounded, or impedance-grounded power systems.
Connecting line corresponding with the safety regulations required
If you use an AC connection cable which does not conform to the local safety
regulations, there is a danger of fire and of electrocution. This can result in
personal injuries or material damage. To avoid dangers, observe the
following: The AC connection cable must be compliant with the safety
regulations and stipulated IDs of the country where the device is to be
installed.
Trademarks
All names identified by ® are registered trademarks of Siemens AG.
The remaining trademarks in this publication may be trademarks whose use
by third parties for their own purposes could violate the rights of the owner.
Disclaimer of Liability
We have reviewed the contents of this publication to ensure consistency
with the hardware and software described. Since variance cannot be precluded
entirely, we cannot guarantee full consistency. However, the information in this
publication is reviewed regularly and any necessary corrections are included in
subsequent editions.
Siemens AG, Division Digital Factory
Postfach 48 48, 90026 NÜRNBERG, GERMANY
Important notes on your device
A5E37501053-AB, 05/2016