Zircon Leak Alert + Quick Start Manual

EN
Leak Alert
Electronic Water Detector
Undetected water can cause thousands of dollars in
damage. Protect your home from potential water damage
+
by keeping a Leak Alert water detector anywhere
™
flooding is a potential danger—near aquariums,
sump pumps, plumbing, washing machines, water heaters,
toilets, basements, and garages.
Flashing LEDs
1. INSTALLING THE BATTERY
Insert a coin between top
and bottom halves of case.
Turn coin to separate.
Connect 9V
battery to clip.
Position battery according to the diagram on
the right. Proper battery position will allow
the unit to float in the event of a flood.
Securely close case.
+
2. TESTING
™
Wet your finger and touch the two
sensing contacts.
A loud, repetitive series of
beeps will sound and the LEDs
will flash red. Dry the
contacts to stop the alarm.
In the event of low battery,
water detector will chirp (short beep
every five seconds). Please replace
with brand new 9V battery immediately.
Sensing Contacts
Battery Access
3. PLACEMENT
Alarm
Place Leak Alert
detector facing up and
flat against the surface,
with metal sensing
contacts down.
Leak Alert
™
detector will not
function properly
with contacts up.
4. FLOODING
Leak Alert
™
will float (if battery is
inserted according to
diagram inside battery
compartment) and alarm
will sound for life of
9V Battery
battery, up to 72 hours.
+
water
™
+
water
+
water detector
5. HELPFUL HINTS
Situation Probable Cause
Alarm sounds, • Battery voltage is low.
but there is no • Water detector is on
water present. a conductive surface
(i.e. metal).
• Ambient moisture
has collected on
metal contacts.
Unit does not sound • Metal contacts are
alarm even when up, not having direct
touching water. contact with water.
• Battery is dead.
Unit does not float. • Battery is not placed in
correct area of case.
REPLACE BATTERY AND RETEST UNIT ANNUALLY.
Leak Alert and Zircon are registered trademarks or trademarks of Zircon Corporation.
Visit www.zircon.com/support
for the most current instructions.
LIMITED 1 YEAR WARRANTY
Zircon Corporation, ("Zircon") warrants this product to be free from defects in
materials and workmanship for one year from the date of purchase. Any in-warranty
defective product returned to Zircon*, freight prepaid with proof of purchase date
and $5.00 to cover postage and handling, will be repaired or replaced at Zircon's
option. This warranty is limited to the electronic circuitry and original case of the
product and specifically excludes damage caused by abuse, unreasonable use
or neglect. This warranty is in lieu of all other warranties, express or implied,
and no other representations or claims of any nature shall bind or obligate Zircon.
Any implied warranties applicable to this product are limited to the one year period
following its purchase. IN NO EVENT WILL ZIRCON BE LIABLE FOR ANY SPECIAL,
INCIDENTAL OR CONSEQUENTIAL DAMAGES RESULTING FROM POSSESSION,
USE OR MALFUNCTION OF THIS PRODUCT.
In accordance with government regulations, you are advised that: (i) some states
do not allow limitations on how long an implied warranty lasts and/or the exclusion
or limitation of incidental or consequential damages, so the above limitations
and/or exclusions may not apply to you, and further. (ii) this warranty gives you
specific legal rights and you may also have other rights which vary from state
to state. Return product freight prepaid with proof of purchase date (dated sales
receipt) and $5.00 to cover postage and handling, to:
Zircon Corporation
*Attn: Returns Department
1580 Dell Avenue
Campbell, CA 95008-06992 USA
Be sure to include your name and return address. Out of warranty service and repair,
where proof of purchase is not provided, shall be returned with repairs charged
C.O.D. Allow 4 to 6 weeks for delivery.
Customer Service: 1-800-245-9265 or 1-408-963-4550
Monday–Friday, 8:00 a.m. to 5:00 p.m. PST
info@zircon.com • www.zircon.com
ZirconCorporation ZirconTV ZirconTools
© 2015 Zircon Corporation • P/N 66912 • Rev A 04/15
Solutions
• Change the battery.
• Place a piece of thin paper
or plastic between water
detector and metal surface.
• Wipe metal contacts dry.
• Make sure metal contacts
are flat on surface where
water is to be detected.
• Replace battery.
• Place unit in face-up
position, open battery
compartment, and position
battery per diagram.
|
ZirconToolPro ZirconTools