HAMPTON BAY 393-810 Instruction Manual page 6

PARTS INCLUDED FOR INSTALLATION (parts are not to scale):
2ea Lock Washers (#3) 2ea Lock Nuts (#4)
2ea Outlet Box Screws (#11) 2ea Mounting Screws (#12)
INSTALLATION INSTRUCTIONS:
1. Screw the two Mounting Screws (#12) into the Cross Bar (#10). Mount the Cross Bar
(#10) to the Outlet Box (#8) using the two Outlet Box Screws (#11). [Make sure the
threads of the Mounting Screws (#12) are facing outside when the Cross Bar (#10) is
attached to the Outlet Box (#8).]
2. Wrap the ground wire from the fixture around the Ground Screw (#13) on the Cross Bar
(#10), and then connect the ground wire from the fixture to the ground wire from the
Outlet Box (#8). Connect the white wire from the fixture to the white wire from the
Outlet Box (#8), and the black wire from the fixture to the black wire from the Outlet
Box (#8). Cover the three wire connections using the three Wire Connectors (#9). Wrap
the three wire connections with electrical tape for a more secure connection. Position the
wires back inside the Outlet Box (#8). Note: If you have questions about the ground
wire, consult your local electrical code for approved grounding methods.
3. Mount the body of the fixture on the wall by aligning the protruding Mounting Screws
(#12) all the way through the holes on the Wall Plate (#1). Be careful not to pinch any of
the wires between the fixture and the Outlet Box (#8). Place a Lock Washer (#3) over
each of the protruding Mounting Screws (#12). Tighten the fixture to the wall by
screwing the two Lock Nuts (#4) onto the two protruding Mounting Screws (#12).
4. Once the fixture is mounted on the wall, caulk the space between the wall and the upper
3/4 area of the Wall Plate (#1) to prevent water seeping into the Outlet Box (#7). Leave
the bottom 1/4 area uncaulked for drainage of any water which might leak into the
enclosure.
5. Installation is complete. Turn on the power at the circuit breaker or fuse box. Turn the
light switch on to activate the fixture.
6. If it is daylight, the light bulb will not illuminate. To test the fixture, cover the Photocell
(#2) with electrical tape to illuminate the light bulb. Once you confirm the light bulb
illuminates, remove the electrical tape.
Page 6
3ea Wire Connectors (#9) 1ea Cross Bar (#10)
1ea Ground Screw (#13)
AVERTISSEMENT:
1. Avant de commencer à installer ce luminaire ou d'enlever l'ancien luminaire,
déconnectez le courant en éteignant le disjoncteur ou en enlevant le fusible
correspondant du coffret à fusibles.
2. CONSULTER UN ELECTRICIEN
QUESTION RELATIVE A L'ELECTRICITE.
3. La luminosité de l'ampoule électrique fluorescente compacte GU-24
fournie avec ce luminaire n'est pas modulable. Ne pas utiliser de dispositif
de modulation de luminosité avec ce luminaire.
4. En cas de questions non relatives à l'électricité à propos de ce luminaire,
veuillez contacter notre centre de Service à la Clientèle au 1-877-527-0313
ou visiter www.homedepot.com. Veuillez indiquer votre UGS 393-810 ou
UPC 6940500310756.
5. Conserver votre reçu et ces Instructions comme Preuve d'Achat.
OUTILS REQUIS POUR L'ASSEMBLAGE & L'INSTALLATION
(non inclus):
Ampoule ( inclus) Lunettes de Protection
(13 watts maxima)
Tournevis à tête plate Tournevis à croisillon
QUALIFIE POUR
Echelle Gants Dénudeur de câbles
électriques
Ruban adhésif Pince pour Joint en Caoutchouc Silicone
isolant câbles électriques pour un usage extérieur
TOUTE
Page 19