Table of Contents
Advertisement
Quick Links
455 Balanced Regulator Installation Guide
E-Mail: KMDSI@KirbyMorgan.com, Web Site:www.KirbyMorgan.com
Diving with compressed breathing gas is a hazardous activity. Even if you do every-
thing right there is always the danger that you may be killed or injured. No piece of
diving equipment can prevent the possibility that you may be killed or injured any time
you enter the water.
The 455 balanced regulator meets or exceeds all performance and testing requirements of all
government and non-government testing agencies throughout the world. Only Kirby Mor-
gan masks and helmets have achieved the Dive Lab
Kirby Morgan, SuperLite
ternational, EXO, REX
Systems, Inc. Use of these terms to describe products that are not manufactured by KMDSI is
illegal.
The two dimensional images (such as photographs and illustrations) of our products are © copyrighted
and trademarks of Kirby Morgan Dive Systems, Inc. The three dimensional forms of our products are
trademark, trade design and trade dress protected.
© MMXV Kirby Morgan Dive Systems, Inc. All rights reserved. This manual is made available for the
express use of the owner of this Kirby Morgan product. No part of this manual may be reproduced,
stored in any retrieval system, or transmitted, or used in any form or by any means, whether graphic,
electronic, mechanical, photocopy, or otherwise by technology known or unknown, without the prior
written permission of Kirby Morgan Dive Systems, Inc.
K
irby
KMDSI Part #100-204
Patented, patents pending, foreign patents apply
Kirby Morgan Dive Systems, Inc.
1430 Jason Way
Santa Maria, CA 93455, USA
Telephone (805) 928-7772, FAX (805) 928-0342
B WARNING
, BandMask, Band Mask, KMB, KMB-Band Mask, DSI, Diving Systems In-
®
, SuperFlow
and DECA are all registered trademarks of Kirby Morgan Dive
®
®
M
organ
TM
, CR (Commercial Rated) mark.
®
®
Advertisement
Table of Contents
Related Manuals for Kirby Morgan 455
Summary of Contents for Kirby Morgan 455
- Page 1 © MMXV Kirby Morgan Dive Systems, Inc. All rights reserved. This manual is made available for the express use of the owner of this Kirby Morgan product. No part of this manual may be reproduced, stored in any retrieval system, or transmitted, or used in any form or by any means, whether graphic, electronic, mechanical, photocopy, or otherwise by technology known or unknown, without the prior written permission of Kirby Morgan Dive Systems, Inc.
-
Page 2: Table Of Contents
The bent tube assembly can be rotated back and forth to aid removal, if nec- essary. INSTL-2 © MMXV Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 150205001... -
Page 3: Nose Block Device Removal
Take care not to lose the whisker spacers. INSTL-3 © MMXV Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 150205001... -
Page 4: Installation Of The 455 Balanced Regulator
1) Lightly lubricate the bent tube O-ring and in- stall into the O-ring groove at the regulator end of the bent tube, then install a new Teflon O-ring ® at the side block end. INSTL-4 © MMXV Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 150205001... -
Page 5: Oral Nasal Mask And Microphone Installation
When a small amount of resis- packing nut and the knob. tance is felt, lock it into place with the jam nut. 4) Tighten the packing nut until snug. Do not INSTL-5 © MMXV Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 150205001... - Page 6 NOTE: For all maintenance and adjustment procedures, refer to the 455 Balanced Regu- lator module found in the “Manuals and Ex- ploded Views” link under the “Support” link at www.kirbymorgan.com. INSTL-6 © MMXV Kirby Morgan Dive Systems, Inc. All rights reserved. Document # 150205001...
- Page 7 This page intentionally left blank.
- Page 8 Kirby Morgan Dive Systems, Inc. 1430 Jason Way Santa Maria, CA 93455, USA Telephone (805) 928-7772, FAX (805) 928-0342 E-Mail: KMDSI@KirbyMorgan.com, Web Site:www.KirbyMorgan.com...