Advertisement
15-20. PRESET STATION MEMORY AND TOP/>||, INT, RPT, RDM BUTTONS
a) During radio mode:
When pressed briefly, these buttons select a preset station directly.If the six buttons
are pressed for more than 2 seconds, the station currently being listened to is
memorized into the selected preset button.
b) During SD/MMC & USB mode:
Press the TOP/>|| button briefly to interrupt the playback of the SD/MMC card or
USB stick.
Press again to resume normal playback.
Press the INT button to play the first 10 seconds part of each track, and the LCD will
display INT ON.
Press again to stop scan, while the currently selected track will be played, and the
LCD will display INT OFF.
Press the RPT button to play the current track repeatedly, and the LCD will display
RPT ONE.
Press again to cancel this function, and the LCD will display RPT OFF.
Press the RPT button twice continuously to play the tracks in the current folder
repeatedly and the LCD display will show RPT ABM.
Press the RDM button to play all tracks in random order, and the LCD will display
RDM ON.
Press again to cancel this function, and the LCD will display RDM OFF.
Press the radio preset button 6 and 5 button to move up and down10 tracks at a time.
When the remaining total tracks are less than 10, then both buttons are inactive.
C) During IPOD mode:
Press the TOP/>|| button briefly to interrupt the playing track.
Press again to resume normal playback.
Press the RPT button to play the current track repeatedly,
Press again to cancel this function.
Press the RDM button to play all tracks in random order.
Press again to cancel this function.
press BAND button to MEMU select, press 5 and 6 to up and down, and then
press 2 to confirm the selecting.
21. SCAN BUTTON
Press the SCAN button to scan the radio frequency. If a valid signal has been
detected, the current frequency will hold and beginblinking for 5 seconds, then
press SCAN again to stop scan and remain on the current frequency; otherwise,
the radio will go on to scan the other radio frequency 5 seconds later.
22.AUX INPUT JACK
Press the mode button to select auxiliary input playing mode. You can connect any
matched external audio device to the auxiliary input jack. Use the volume control to
adjust volume.
23. USB SOCKET
When needing to play the file in the USB stick, insert the USB stick into the USB
socket. The system will change into the USB mode automatically, and then play the
first file in the USB.
PDF created with FinePrint pdfFactory trial version
Page 5
http://www.pdffactory.com
24. SD CARD SLOT
When you need to play the file in the MMC/SD card, insert the MMC/SD card into the
MMC/SD card slot. The system will change into the MMC/SD mode automatically,
and then play the first file in the MMC/SD.
Note:
When MMC/SD card and USB stick are both inserted into their slot or socket, the
system will change into the playback mode of the latter one.
25. RESET BUTTON
Before operating the unit for the first time, or after replacing the car battery or
changing the connections. You must reset the unit.
Press this button with a cuspidal object. This operation will erase the clock setting
and some stored contents.
INSTALLATION METHOD
This is an anti-theft installation method.
The main unit has a METAL MOUNTING SLEEVE.
Please connect the wiring, eg, the Power Supply, the Speakers and the Antenna
according to the requirements of this Instruction Manual, then install the metal
mounting sleeve into the car as per the diagram illustrated below.
For optimum anti-skip capability of the unit,
please ensure the metal support strap is
bolted firmly to the car chassis.
METAL
SUPPORT STARP
DASHBOARD
METAL MOUNTING SLEEVE
The
front panel
with screws, cannot be push out
To remove the unit out of the metal mounting sleeve,
remove the two plastic first and then insert the two supplied KEYS
into the left and right side slots of the chassis at the same time.
Bend the tabs on the metal mounting
sleeve against the DASHBOARD with
a screwdriver.
SOFT PLASTIC TRIM RING
FRONT PANEL
Page 6
Advertisement
