Advertisement
TROUBLE SHOOTING
Before using the check list please make all the connections first.
If you still have questions after going through the checklist, please consult
your local customer service representative.
Common Symptoms
Cause
The car ignition is switched off.
There is no power.
The fuse has blown.
The volume control is set too low.
There is no sound.
The device has not been correctly
connected.
The operation keys
The built-in microcomputer is not
do not work
operating properly due to noise
No radio reception.
The antenna cable is not connected.
In automatic search
mode the radio does
The transmission signals are too
not stop at a trans-
weak.
mitting station.
PDF created with FinePrint pdfFactory trial version
Solution
If the power supply is properly connected to
the car accessory, switch the ignition key to
"
ON
"
or " ACC
" .
Replace another fuse according to the wiring
diagram.
Turn up the volume properly.
Check the power and earth connection
according to the wiring diagram.
Switch the device off and on again. Or press
the RESET button to resume the program.
Insert the antenna cable firmly into the
antenna socket of the device.
Tune in to a radio station manually.
Page 7
http://www.pdffactory.com
* When TA is on, SEEK, (SCAN), AUTO MEMORY function can be received or saved
only when traffic program identification code has been received.
When TA is ON, traffic program identification code is not received during specified time.
13.AF [ALTERNATIVE FREQUENCIES] BUTTON
When pressed briefly, AF switching mode is selected and the state of AF switching
mode is displayed by AF segment in display.
Segment off: AF switching mode off.
Segment on: AF switching mode on, and has RDS information.
Segment flashing: AF switching mode on, but RDS information is not received yet.
When AF switching mode is selected, the radio checks the signal strength of AF all
the time. The interval of checking time of each AFs depends on the signal strength
of current station, from a few minutes for a strong station to a few seconds for weak
station. Every time that new AF is stronger than current station, it switches over to
that frequency for very short time, and NEW FREQUENCY is displayed for 1-2
seconds.
Because the mute time of AF switching or checking time is very short, it is almost
inaudible in case of normal program.
During FM mode, when AF is on, SEEK, (SCAN), AUTO-MEMORY function can only
receive and save RDS program.
14. AS/PS BUTTON (Auto-storage /Preset scan)
During radio mode:
1) When pressing and holding for more than 1 second, the radio searches from the
current frequency and checks the signal strength level until 6 station are found. And
then the 6 stations are preset to the corresponding preset memory numbered bank.
The auto-storage operation is implemented in each selected band. When the
auto-storage operation is finished, the radio executes the Preset scan.
2) When briefly pressing, the radio searches for each preset station in the current
band and holds at that preset number for 5 seconds while releasing mute, and then
searches again.
During SD/MMC or USB mode:
Press the AS/PS button, this activates TRACK SEARCH mode:
In TRACK SEARCH mode, the LCD will display TRK T "0" and flashes the biggest
digit 0 that the SD/MMC card or USB stick contains.
Then press the VOL+ or VOL- button to select the number of the flashing digit from
0 ~ 9. Then press SEL button to confirm the number and flash next smaller digit 0.
With the same means, select the number of the flashing digit with VOL+/-.
After finishing selecting the number of all flashing digit, press SEL button to play
the track of the selected serial number.
Press the AS/PS button twice, this activates TRACK SEARCH mode:
In FIRST CHARACTER SEARCH mode, the LCD will display A--......, If there are
files names its first character A, the ......is the first file name, its first character
is A by the order of A~Z and 0~9; otherwise, the ......is NONE. (If there are some
songs in character A, press the >>I and I<< to select your favourite.)Then press the
'
VOL+ or VOL- button to select file s first character by the order of A~Z and 0~9.
Press the AS/PS button thrice, this activates TRACK SEARCH mode:
In DIRECTORY SEARCH mode, the LCD will display the root folder(if there is no
root folder, it will find a root folder named ROOT). Then press the VOL+ or VOL-
button to select your desired folder and then press >> | or |<< button to select your
desired track in the folder.
Page 4
Advertisement
