Humminbird 700 Series Owner's Manual

700 Series™ In-Dash Mounting Kit
Returning Your Unit for Service
Before sending your unit in for repair, please contact the factory, either by
phone or by email, to obtain a Repair Authorization Number for your unit.
NOTE: Please do not return your Humminbird® to the store for service.
Please have your product model name and serial number available
before calling the factory. If you contact the factory by e-mail, please
include your product model name and serial number in the e-mail, and
use Request for Repair Authorization Number for your e-mail subject
header. You should include your Repair Authorization Number in all
subsequent communications about your unit.
For IN-WARRANTY service, complete the following steps:
• Obtain a Repair Authorization Number from the Humminbird®
Customer Resource Center.
• Tag product with your name, street address, phone number and
your assigned Repair Authorization Number.
• Include a brief written description of the problem.
• Include a copy of your receipt (to show proof and date of
purchase).
• Return product freight prepaid to Humminbird®, using an insured
carrier with delivery confirmation.
For OUT-OF-WARRANTY service, complete the following steps:
• Obtain a Repair Authorization Number from the Humminbird®
Customer Resource Center.
• Include payment in the form of credit card number and expiration
date, money order or personal check. Please do not send cash.
• Tag product with your name, street address, phone number and
your assigned Repair Authorization Number.
• Include a brief written description of the problem.
• Return product freight prepaid to Humminbird®, using an insured
carrier with delivery confirmation.
Contact Humminbird®
Contact the Humminbird® Customer Resource Center
in any of the following ways:
By Telephone
(Monday - Friday 8:00 a.m. to 4:30 p.m. Central Standard Time):
1-800-633-1468
By e-mail
(typically we respond to your e-mail within three business days):
cservice@johnsonoutdoors.com
For direct shipping, our address is:
Humminbird
Service Department
678 Humminbird Lane
Eufaula, AL 36027 USA
ENVIRONMENTAL COMPLIANCE STATEMENT: It is the intention of
Johnson Outdoors Inc. to be a responsible corporate citizen, operating
in compliance with known and applicable environmental regulations,
and a good neighbor in the communities where we make or sell our
products.
WEEE DIRECTIVE: EU Directive 2002/96/EC "Waste of Electrical and
Electronic Equipment Directive (WEEE)" impacts most distributors,
sellers, and manufacturers of consumer electronics in the European
Union. The WEEE Directive requires the producer of consumer
electronics to take responsibility for the management of waste from
their products to achieve environmentally responsible disposal during
the product life cycle.
WEEE compliance may not be required in your location for electrical &
electronic equipment (EEE), nor may it be required for EEE designed and
intended as fixed or temporary installation in transportation vehicles
such as automobiles, aircraft, and boats. In some European Union
member states, these vehicles are considered outside of the scope of
the Directive, and EEE for those applications can be considered
excluded from the WEEE Directive requirement.
This symbol (WEEE wheelie bin) on product indicates the
product must not be disposed of with other household refuse. It
must be disposed of and collected for recycling and recovery of
waste EEE. Johnson Outdoors Inc. will mark all EEE products in
accordance with the WEEE Directive. It is our goal to comply in the
collection, treatment, recovery, and environmentally sound disposal of
those products; however, these requirement do vary within European
Union member states. For more information about where you should
dispose of your waste equipment for recycling and recovery and/or your
European Union member state requirements, please contact your dealer
or distributor from which your product was purchased.
© 2008 Humminbird®, Eufaula AL, USA.
All rights reserved.
4
531462-1_C
700 Series™ In-Dash Mounting Kit
Thank You
Thank you for choosing Humminbird®, America's #1 name in fishfinders. Humminbird® has built its reputation
by designing and manufacturing top-quality, thoroughly reliable marine equipment. Genuine Humminbird®
accessories offer the opportunity to upgrade and expand the capabilities of your Humminbird® product.
Your Humminbird® accessory is designed for trouble-free use in even the harshest marine environment. In the
unlikely event that your Humminbird® accessory does require repairs, we offer an exclusive Service Policy - free
of charge during the first year after purchase, and available at a reasonable rate after the one-year period. For
complete details, see the Warranty section included in this manual.
Contact our Customer Resource Center at either 1-800-633-1468 or visit our website at www.humminbird.com.
Installation Overview
Following are instructions for the recessed installation of the 700 Series
dash. Before you start installing the 700 Series
carefully in order to get the full benefit from your Humminbird® accessory.
If you find that any items are missing from your installation kit, call our Customer Resource Center at
1-800-633-1468 or visit our website at www.humminbird.com.
In addition to the hardware supplied with your In-Dash Mounting Kit, you will need a reciprocating saw for
cutting the dash material and masking tape to hold the mounting template in place.
In-Dash Mounting
To in-dash mount the 700 Series TM control head, start by placing the components on the surfaces where you
intend to install them before installation. Make sure that the surfaces you have chosen provide adequate
protection from wave shock and that all cables can reach the control head.
NOTE: If a cable is too short for your application, extension cables are available. Call Humminbird®
Customer Support at 1-800-633-1468 for more information.
1. Locate a suitable, flat area of the dash to mount the control head. The control head requires a depth of
at least 3 inches (76 mm).
2. Tape the paper In-Dash Mounting template to the desired in-dash mounting location.
3. At a location inside the dotted line on the template, drill a hole large enough to insert the blade of the
reciprocating saw. Carefully begin cutting toward the dotted line, then follow the dotted line around the
template. Remove the template when finished.
4. Insert and tighten the two threaded rods into the two threaded inserts located on the back side of the
control head. Peel off the adhesive-backed foam pads and place them on the back of the control head;
make sure you notice the difference between the longer top/bottom and shorter side pads.
TM control head into a hole in the
TM control head, we encourage you to read these instructions
1
531462-1_C
Applying the Foam Pads
© 2008 Humminbird®, Eufaula AL, USA.
All rights reserved.