Taymor BRENTWOOD 06-4804P Installation Instructions

INSTALLATION INSTRUCTIONS
BRENTWOOD 06-4804P / 06-4804BRN
TWO HANDLE LAVATORY FAUCET
THIS FAUCET MEETS OR EXCEEDS THE FOLLOWING STANDARDS:
cUPC, ASME A112.18.1, NSF-61 AND LOW LEAD COMPLIANT
THANK YOU FOR PURCHASING THIS TAYMOR PRODUCT. ALL TAYMOR PRODUCTS ARE CAREFULLY
ENGINEERED AND FACTORY TESTED TO PROVIDE LONG TROUBLE-FREE USE UNDER NORMAL CONDITIONS.
HAVE BASIC TOOLS READY
1
RECOMMENDED TOOLS:
Teflon tape Screwdrivers Adjustable
Flashlight
wrench and
pipe wrench
WARNING: READ ALL the instructions completely before beginning.
READ ALL warnings, care and maintenance information.
Taymor recommends calling a professional if you are uncertain about installing this product!
This product should be installed in accordance with all local and provincial plumbing and building codes.
Need Help? Please call our toll-free Customer Support line at
(WEST) 1-800-267-4774 (EAST ) 1-800-387-7064 for additional assistance or service.
TURN OFF THE MAIN WATER SUPPLY
2
Locate water supply inlets and shut off water supply valves. These are usually found under
the sink.
TURN OFF
GASKET & FAUCET INSTALLATION
3
A) Apply a bead of plumber's putty or silicone caulk around the sink openings.
B) Install the gasket over the three holes in your sink.
C) Install faucet shanks through the holes of the sink. Centre the faucet body on the sink.
Don't use plumber's putty on cultured marble or other composite sinks.
Putty will discolour the sink.
A
HAND TIGHTEN THE MOUNTING NUTS
4
From underneath the sink, hand tighten the mounting nuts. Tighten gently until snug and alternate from
side to side to seat the faucet body evenly.
Don't over tighten
Your installation may require new supply
lines. (Supply lines are not included.)
Torque wrench Safety goggles Plumber's putty
TURN OFF
B C
1
ATTACH THE HOT AND COLD SUPPLY LINES
5
Apply Teflon tape onto threaded ends of faucet inlets.
Connect water supply lines to faucet inlets. Hot water supply lines go into left inlet. Cold water supply
lines go into right inlet. (Supply lines are not included).
FOR PLASTIC AND BRAIDED
STAINLESS STEEL SUPPLY TUBES
THESE SUPPLY TUBES HAVE INTEGRAL NUTS.
SCREW THE NUT ONTO THE FAUCET INLET.
TORQUE
22 – 30 FT/LBS.
INSTALLING POP-UP DRAIN
6
A) Remove pop-up plunger (A) and flange (B). Screw locknut (C) all the way down. Push gasket
(D) down. Apply silicone to underside of flange (B).
B) Insert body into sink (from underneath). Screw flange onto body. Pivot hole (E) must face
the back of the sink.
C) Tighten locknut (C) and gasket (D) but do not overtighten. Remove pivot ball retaining nut (E).
D) Slide pivot rod (F) into the eye of the pop-up plunger (A). Hand tighten retaining nut.
E) Slide pivot rod (F) through hole in spring clip (G), then through lever strap (H) and back
Silicone caulk
through spring clip (G).
F) Insert lift rod (I) down through faucet body and then into lever strap (H). Tighten screw (J).
Connect assembly to drain.
A
A
B
D
C B
A
D
A
FLUSHING & AERATOR CLEANING
7
Remove the aerator by turning it counterclockwise. Remove the internal parts of the aerator by push-
ing them out with your fingers. Remove any debris. Turn on hot and cold water supplies. Turn faucet
handles all the way on and run water through the spout for about a minute to remove debris. While
water is running check all connections for leaks. Reassemble the aerator and screw it back into the
spout hand tight.
29 - SPOUT
28 - WASHER
27 - AERATOR
26 - AERATOR SHELL
EXPLODED
8
DIAGRAM FOR
REFERENCE
MAINTENANCE Your new
faucet is designed for years
of trouble-free performance.
Keep it looking new by
cleaning it periodically with
a soft cloth. Avoid abrasive
cleaners, steel wool and
harsh chemicals as these
will dull the finish and void
your warranty.
CUSTOMER SERVICE WEST 1-800-267-4774 | EAST 1-800-387-7064 | taymor.com
FOR 3/8" O.D. BALL-NOSE SUPPLY TUBES
IF THE SUPPLY TUBE END HAS A BULBOUS SHAPE,
USE THE SUPPLIED COUPLING NUTS.
TORQUE
22 – 30 FT/LBS.
B C
B
E
E
H
F
F
G
1 - SPOUT HEAD
2 - SLEEVE CAP
3 - INDEX
25 - WASHER
4 - SCREW
24 - O-RING
5 - CONNECTOR
6 - BOLT
23 - TUBE
22 - O-RING
21 - SPOUT SEAT
9 - HANDLE SEAT
10 - BONNET
20 - O-RING
11 - WASHER
12 - CARTRIDGE
13 - ESCUTCHEON
14 - BODY
15 - SCREWS
16 - BASE
PLATE
18 - MOUNTING
NUT
19 - COUPLING
NUT
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.
D
E
C
F
I
J
H
7 - HANDLE
8 - LIFT ROD & KNOB
17 - POP-UP
ASSEMBLY