Taymor SCENE STEALER 06-8880S Installation Instructions

INSTALLATION INSTRUCTIONS
SCENE STEALER 06-8880S
SINGLE HANDLE KITCHEN FAUCET
THIS FAUCET MEETS OR EXCEEDS THE FOLLOWING STANDARDS:
cUPC, ASME A112.18.1, NSF-61 AND LOW LEAD COMPLIANT
THANK YOU FOR PURCHASING THIS TAYMOR PRODUCT. ALL TAYMOR PRODUCTS ARE CAREFULLY
ENGINEERED AND FACTORY TESTED TO PROVIDE LONG TROUBLE-FREE USE UNDER NORMAL CONDITIONS.
HAVE BASIC TOOLS READY
1
RECOMMENDED TOOLS:
Teflon tape Screwdrivers Adjustable
wrench and
pipe wrench
WARNING: READ ALL the instructions completely before beginning.
READ ALL warnings, care and maintenance information.
Taymor recommends calling a professional if you are uncertain about installing this product!
This product should be installed in accordance with all local and provincial plumbing and building codes.
Need Help? Please call our toll-free Customer Support line at
(WEST) 1-800-267-4774 (EAST ) 1-800-387-7064 for additional assistance or service.
TURN OFF THE MAIN WATER SUPPLY
2
Locate water supply inlets and shut off water supply valves. These are usually found under
the sink.
TURN OFF
FAUCET INSTALLATION
3
1) Retract pull-out hose (1) up through faucet body, until the pull-out hose fitting is
flush with the bottom of mounting shank (2). Do not pull hose fitting past the mounting shank.
Insert faucet body through the hole. Note: Do not feed the pull-out hose (1) back down
through the spout until step 4.
2) Install rubber washer (1), metal washer (2) onto the threaded mounting shank. Thread
nut (3) onto mounting shank. Do not overtighten.
3) Screw quick connector (2) to the free end of pull-out hose (1).
4)
Align block (1) and tabs on quick connect. Push quick connect housing firmly upward and snap onto receiving
block. Pull down moderately to ensure connection has been made. After connecting the hose, install the
weight at the lowest point of the hose (2). If it is necessary to remove quick connect, squeeze tabs on hose
between index finger and thumb, then pull down to disconnect.
Don't use plumber's putty on cultured marble or other composite sinks. Putty will
discolour the sink.
1
1
2
3
2
1
Your installation may require new supply
lines. (Supply lines are not included.)
Flashlight Safety goggles
Torque wrench
TURN OFF
2
1
2
3
4
1
2
ATTACH THE HOT AND COLD SUPPLY LINES
4
Thread the nut (1) on supply line onto outlet of water supply valve (2) and tighten with a wrench.
Do not over tighten.
IMPORTANT
FLUSHING THE WATER LINES
5
Turn on hot and cold water supplies. Pull the hose assembly out of the spout and remove the spray
head by unscrewing it from the hose counterclockwise. Be sure to hold the end of the hose down into
the sink and turn the faucet on to the warm position where it mixes hot and cold water. Flush water
lines for one minute. Check for leaks. Re-tighten any connections if necessary, but do not overtight-
en. Reinstall spray head by hand tightening it back onto the spray hose.
Silicone caulk
EXPLODED DIAGRAM FOR REFERENCE
6
MAINTENANCE Your new faucet is designed for years of trouble-free performance. Keep it looking
new by cleaning it periodically with a soft cloth. Avoid abrasive cleaners, steel wool and harsh
chemicals as these will dull the finish and void your warranty.
1 - SPOUT
2 - C-RING
3 - O-RING
4 - SHANK
6 - SLEEVE
7 - BODY
8 - NUT
9 - O-RING
10 - WASHER
31 - HOSE
11 - SHANK
12 - CAP
13 - WASHER
14 - NUT
32 - WEIGHT
15 - SCREW
CUSTOMER SERVICE WEST 1-800-267-4774 | EAST 1-800-387-7064 | taymor.com
1
2
16 - CAP
17 - CHECK VALVE
24 - INDEX
25 - SET SCREW
21 - CARTRIDGE
20 - O-RING
19 - BASE SEAT
27 - OUTLET HOSE
28 - HOSE
29 - CHECK VALVE
30 - C-CLIP
® REGISTERED TRADEMARK OF TAYMOR INDUSTRIES LTD.
18 - SPOUT
26 - HANDLE
23 - COVER
22 - RETAINER
OCT. 2018