How To Initialize The Setting; Basic Connection Example - JVC TM-H1750CG Operating Instructions Manual

HOW TO INITIALIZE THE
SETTING
SCREEN DISPLAY AND SELECTIONS IN THE
<SET-UP MENU> RESET MODE
You can set <MENU> and <SET-UP MENU> screen items, picture adjustment items and
the volume level to their factory-set (initial) values.
1. Press the Power ( ) switch to turn the power
OFF (activate the standby mode).
POWER
2. While pressing both MENU button and CHROMA/
PHASE button, press the Power ( ) switch to turn
the power ON.
The <SET-UP MENU> RESET screen is displayed.
* The screen automatically disappears when no operation
CHROMA MENU POWER
is performed after about 5 minutes.
PHASE Note:
● The <SET-UP MENU> RESET screen will not be
displayed if the MENU or CHROMA/PHASE buttons are
pressed for a very short time. Keep pressing them until
the display screen appears.
3. Setting
Initialization is required.
Press the VOLUME/SELECT [+] button.
VOLUME/SELECT
* Initialization is completed, and the <SET-UP MENU>
RESET screen disappears.
Initialization is not required.
Press the MENU button.
MENU
* Initialization is aborted, and the <SET-UP MENU>
RESET screen disappears.
14
All manuals and user guides at all-guides.com
<SET-UP MENU> RESET screen
<SET–UP MENU> RESET
Are you sure ?
"Yes" then <+>
"No" then <MENU>
Initial settings
Initialization
Functions (Items)
(setting)
APERTURE 00
ADJ. BAR POSI LOWER
COLOR TEMP 6500
COLOR SYSTEM AUTO
COMPO. LEVEL 00
RUSH DELAY STD
PICTURE SUB ADJ.
CONTRAST 00
BRIGHT 00
CHROMA 00
PHASE 00
H. POSITION 00
V. POSITION 00
WHITE BALANCE
R. CUT OFF 00
G. CUT OFF 00
B. CUT OFF 00
R. DRIVE 00
B. DRIVE 00
CONTROL LOCK OFF
STATUS DISPLAY ON
REMOTE SYSTEM MAKE
INPUT REMOTE A – D
CHROMA 00
PHASE 00
CONTRAST 00
BRIGHT 00
VOLUME 20

BASIC CONNECTION EXAMPLE

Notes:
•
Before connecting your system, make sure that all units are turned off.
•
The illustration below shows some examples of different connections. Terminal connections may differ depending on the component connected.
Be sure to refer to the instructions provided with the unit(s) you are connecting.
•
Each pair of input (IN) and output (OUT) terminals are bridge-connected.
•
If you're not connecting any equipment to a bridged output (OUT) terminal, be sure not to connect any other cables to the bridged output (OUT)
terminal as this will cause the terminating resistance switch to open (auto terminate function).
•
When making a bridge connection, connect the input (IN) and output (OUT) terminals on the monitor to separate video components.
(For example, if both terminals are connected to the same VCR, resonance may occur except during playback. This is caused by the same video
signal "looping" between the VCRs, and is not a malfunction.)
•
Select the video input signal (INPUT A(VIDEO) or INPUT B (VIDEO/Y/C)) with the INPUT SELECT buttons on the front panel. When both
VIDEO B terminals are connected (input) at the same time, the Y/C terminal has priority.
VIDEO A Connection Example (Select Input A (VIDEO))
VIDEO A
Video
(Video signal cable)
Video Camera
VIDEO B
Audio
Video Monitor
(Audio signal cable)
OUT
AUDIO A
VCR
AUDIO B
VIDEO B (VIDEO) Connection
Example (Select Input B (VIDEO))
Video
Video Camera
(Video signal cable)
Video Monitor
Audio
(Audio signal cable)
VCR
Video
(Video signal cable)
IN OUT
Video
(Video signal cable)
IN OUT
IN Y/C
Audio
(Audio signal cable)
IN OUT
Video Monitor
Audio
(Audio signal
OUT
IN
cable)
VCR
Video Monitor
: Signal Flow
15