Preparation; How To Handle Basic Operations - JVC TM-H1750CG Operating Instructions Manual

PREPARATION

INSTALLING THE INPUT CARD
1. Turn off the Color Video Monitor's main power and unplug the power cable
from the AC outlet.
2. Unscrew the screws and remove the slot cover from the slot (on the rear side
of the monitor) in which you are going to install the card.
REMOTE
VIDEO A
IN
VIDEO B
IN
IN
3. Insert the Input Card's board (green-colored) into the slot, fitting the board into
the guide rails on the top and bottom of the slot.
Fit the board to
the guide rails.
Knob
Input card (the illustration
shown is of the IF-C01COMG)
Knob
4. Push the Input Card in so that its front panel touches the monitor's rear panel.
5. Secure the Input Card by replacing the screws removed in Procedure 2.
REMOTE
VIDEO A
IN
VIDEO B
IN
IN
NOTE : Do not touch the terminal connected to the monitor or board pattern.
Do not remove slot covers from the monitor's slots if they are not in use.
8
All manuals and user guides at all-guides.com
Rear side of the TM-H1750CG
color video monitor
Slot cover
OUT
OUT
Y/C
REMOTE
VIDEO A
Guide rails
IN OUT
VIDEO B
IN OUT
IN Y/C
OUT
OUT
Y/C
HOW TO HANDLE BASIC
OPERATIONS
BASIC OPERATION
1. Press the main power switch to turn on the power.
2. Press the POWER switch to turn on the power.
ON : Power turns ON. (Power indicator: lit)
POWER
Green : The main power is ON, and the monitor's
power is ON (in the normal operation mode).
OFF : Power turns OFF. (Power indicator: unlit)
Orange : The main power is ON, but the monitor's
power is OFF (in the standby mode)
Unlit : The main power is OFF.
3. Press the INPUT SELECT buttons to choose input.
Select video/audio signals input to terminals on the rear
panel. The selected button lights in green.
A B C SLOT D
INPUT
Terminals on the rear panel
SELECT
INPUT SELECT
Video signal input
buttons
1
Input A
VIDEO A terminal
(VIDEO)
2
Input B VIDEO B terminal
(VIDEO/Y/C)
VIDEO B (Y/C) terminal
3
Input C
Refer to page 7 for details about the input terminals
4
Input D on each card and the INPUT SELECT button.
Note: The Y/C (S-video) terminal has priority.
4. Press the VOLUME/SELECT buttons to adjust the
speaker volume.
Press this button to display the speaker volume level on the
VOLUME/SELECT screen.
+ : The Built-in speaker volume is increased. (00 = 50)
– : The Built-in speaker volume is decreased. (50 = 00)
* Screen indication will disappear about 10 seconds after operating.
* The on-screen display goes off when you press MENU button.
PICTURE ADJUSTMENT
1. Press select buttons corresponding to the item
you want to adjust.
The item you select is displayed on the screen.
CHROMA CONTRAST
1
Chorma control : Press the CHROMA/PHASE button once.
2
Phase control : Press the CHROMA/PHASE button twice.
3
Contrast control : Press the CONTRAST/BRIGHT button once.
PHASE BRIGHT
4
Brightness control : Press the CONTRAST/BRIGHT button twice.
* Pressing the CHROMA/PHASE button and CONTRAST/BRIGHT button
alternately while the item is shown on screen restores the previous status.
When no item is shown on screen, CHROMA and CONTRAST have priority.
2. Adjust with the VOLUME/SELECT buttons.
VOLUME/SELECT button
Items
VOLUME/SELECT
–
CHROMA
lighter
(Chroma)
PHASE
reddish
(Phase)
CONTRAST
lower
(Contrast)
BRIGHT
darker
(Brightness)
* Screen indication will disappear about 10 seconds after operating.
* The on-screen display goes off when you press MENU button.
STATUS indication
(PAL or NTSC)
PAL
About the STATUS indication
● With the COLOR SYSTEM setting set
to AUTO mode, when you turn on the
power or select inputs, the color
system indication appears for about
3 seconds on the screen while PAL or
Audio signal input
NTSC signals are being detected.
AUDIO A terminal
It does not appear when receiving a
B/W signal or when no signal is input.
AUDIO B terminal
Refer to page 11 for more information
about COLOR SYSTEM setting and
page 12 for more information about
STATUS indication setting.
00 ~ 50
VOLUME : 20
– +
UPPER
–40 ~ +40
PHASE : 00
PHASE : 00
– +
Notes:
LOWER
● Phase control is effective only in the
NTSC color system mode.
+
● Chroma control is not effective when
receiving RGB and B/W or when no
deeper
signal is input. (Except when a
component signal is input.)
greenish
● When CHROMA is adjusted to "–40,"
the picture becomes less colorful.
● "NO EFFECT" is displayed (for about
higher
3 seconds) when your selected
function has no effect.
brighter
● To change the display position on
screen, set UPPER or LOWER with
ADJ. BAR POSI.
9