Table of Contents
Advertisement
Quick Links
DS8100A-3002
QUICK REFERENCE GUIDE
This manual illustrates a typical Local Lonworks network application. For more details refer
to the DS8100A Reference Manual available on the CD. For complete scanner configuration
using the Genius™ configuration program refer to the Help On Line.
NOTE
821001264 (Rev. D)
Advertisement
Table of Contents
Related Manuals for Datalogic DS8100A-3002
Summary of Contents for Datalogic DS8100A-3002
- Page 1 DS8100A-3002 QUICK REFERENCE GUIDE This manual illustrates a typical Local Lonworks network application. For more details refer to the DS8100A Reference Manual available on the CD. For complete scanner configuration using the Genius™ configuration program refer to the Help On Line.
-
Page 2: Services And Support
- Material Return Authorization LEGAL NOTICES © 2005 - 2010 Datalogic Automation S.r.l. ALL RIGHTS RESERVED. Protected to the fullest extent under U.S. and international laws. Copying, or altering of this document is prohibited without express written consent from Datalogic Automation S.r.l. - Page 3 DS8100A-3002 QUICK GUIDE DS8100A-3002 GENERAL VIEW Figure A Laser Beam Output Window Figure B Programming Keypad TX Data LED (Green) Power On LED (Green) Network LED (Red) LCD Display Phase On LED (Yellow) Encoder LED (Yellow) Figure C Lonworks 17-pin Male Connector...
- Page 4 DS8100A-3002 QUICK GUIDE CONNECTIVITY Local Lonworks Network Host ETHERNET CAB-SC6103 Cable VAC INPUT SC6000 Power/Net CAB-SC6013 CAB-SC6003 Extended I/O LONWORKS ENCODER BTK-8500 CAB-85xx Bus Return PS Aux CAB-85xx CAB-85xx CAB-85xx CAB-85xx BTK-8500 Bus Return DX8200A-3002 DS8100A-3002 DX8200A-3002 DS8100A-3002 CAB-85xx CAB-85xx...
- Page 5 DS8100A-3002 QUICK GUIDE to Host ETHERNET SC6000 VAC INPUT CAB-SC6103 Power/Net CAB-SC6013 Working CAB-SC6003 Controller Extended I/O LONWORKS ENCODER CAB-85xx PS Aux CAB-85xx CAB-85xx CAB-85xx BTK-8500 DX8200A-3002 DS8100A-3002 DX8200A-3002 DS8100A-3002 Redundancy CAB-PWO 03 to Host ETHERNET VAC INPUT SC6000 Power/Net...
-
Page 6: Electrical Connections
DS8100A-3002 QUICK GUIDE SC6000 Working Conveyor SC6000 Protecting Example Redundant Reading Station ELECTRICAL CONNECTIONS Two 17-pin connectors provide access to the scanner’s local Lonworks network used for both input and output connections to build a multi-sided or omni-station system. 17-pin Lonworks Connector Pinout... -
Page 7: Technical Features
DS8100A-3002 QUICK GUIDE APPENDIX TECHNICAL FEATURES ELECTRICAL FEATURES Supply Voltage 20 to 30 Vdc Power Consumption 1.0 to 0.67 A; 20 W typical 1.5 to 1.0 A; 30 W Max. (including startup current) Communication Interfaces Auxiliary Baud Rate RS232 1200 to 115200... - Page 8 DS8100A-3002 QUICK GUIDE ACCESSORIES Name Description Part Number Power Supply PWO-480 Power and Connect System 480W 93ACC1767 Cables and Terminators BTK-8100 Bus Terminator Kit (5 pcs) 93ACC1090 BTK-8500 IP65 Terminator Kit (2 pcs) 93A051286 CAB-8100 10 wire shielded cable D 9.5 mm – 50 m...
-
Page 9: Mechanical Installation
MECHANICAL INSTALLATION DS8100A-3002 can be installed to operate in any position. There are 16 screw holes (M6 X 8) on the sides of the scanner for mounting. The following diagrams give the overall dimensions of the reader standard model and mounting bracket. -
Page 10: Reading Diagrams
DS8100A-3002 QUICK GUIDE READING DIAGRAMS Note: (0,0) is the center of the laser beam output window. DS8100A-3002 – 0.50 mm/20 mils (in) (cm) CONDITIONS Code = Interleaved 2/5 or Code 39 PCS = 0.90 “Pitch“ angle = 0° “Skew“ angle = 10°... -
Page 11: Laser Safety
WHEN OPEN AVOID EXPOSURE AVOID LASER RADIATION IS EMITTED FROM THIS APERTURE EXPOSURE TO BEAM Laser Safety Label DATALOGIC S.P.A. Via Candini, 2 40012 Calderara di Reno - Bologna - Italy Manufactured Volt LASER LIGHT DO NOT STARE INTO BEAM Model No. -
Page 12: Fcc Compliance
DS8100A-3002 QUICK GUIDE FCC COMPLIANCE Modifications or changes to this equipment without the expressed written approval of Datalogic could void the authority to use the equipment. This device complies with PART 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference which may cause undesired operation.