Troubleshooting; Environmental Protection; Technical Specifications - Metabo CS 23-355 Operating Instructions Manual

en ENGLISH
Removing the cutting disc:
- Press lever for spindle locking knob (8) to the right
and turn the cutting disc by hand until the spindle
locking knob is felt to engage.
- Use the wrench (c) to remove the screw with
clamping flange (b) anti-clockwise.
- Remove cutting disc.
Fitting the cutting disc:
- Put on new cutting disc (a).
- Fit the screw with clamping flange (b).
- Use wrench (c) to lock spindle and tighten screw
with clamping flange (b).
- Check whether the spindle locking knob (8) is
completely disengaged again.
- Clean the dirty machine and remove the grinding
dust.
Regular maintenance:
Oil the following parts at least once a month:
movable parts of the vice.

8. Troubleshooting

Switching on procedures produce brief reductions
in voltage. Unfavourable power conditions can be
detrimental to other devices. Power impedances
smaller than 0.2 ohm should not cause any
malfunction.
9. Accessories
Use only genuine Metabo accessories.
If you need any accessories, check with your
dealer.
For dealers to select the correct accessory, they
need to know the exact model designation of your
power tool.
See page 4.
A Cutting discs: Quality class A 24-M "Original
Cutting"
Aluminum oxide wheels for general purpose
use on steel and other ferrous metals larger
chop saw applications. Excellent rate of cut.
Good wheel life.
B Cutting discs: Quality class A 30-S "LongLife
Original "
Aluminum oxide wheels specially formulated for
dry wall stud applications. Good rate of cut.
Good wheel life.
C Cutting discs: Quality class A 30-R "LongLife
Original"
Aluminum oxide wheels for general purpose
use on steel and other ferrous metals.
Good rate of cut. Good wheel life.
10
a b
8
For a complete range of accessories, see
www.metabo.com or the main catalogue.
c
10. Repairs
Repairs to electrical tools must be carried out
by qualified electricians ONLY!
A defective mains cable must only be replaced with
a special, original mains cable from metabo, which
is available only from the Metabo service.
If you have Metabo electrical tools that require
repairs, please contact your Metabo service centre.
For addresses see www.metabo.com.
You can download spare parts lists from
www.metabo.com.

11. Environmental Protection

The generated grinding dust may contain harmful
substances. Dispose appropriately.
Observe national regulations on environmentally
compatible disposal and on the recycling of disused
machines, packaging and accessories.

12. Technical Specifications

Explanatory notes on the specifications on page 4.
Changes due to technological progress reserved.
U
I
P
1
P
2
n
0
Cutting disc dimensions:
D
max
B
d
H
max 90°
H
max 45°
L
max
m
The technical specifications quoted are subject to
tolerances (in compliance with the relevant valid
standards).
Emission values
These values make it possible to assess the
emissions from the power tool and to compare
different power tools. Depending on the operating
conditions, the condition of the power tool or the
accessories, the actual load may be higher or lower.
For assessment purposes, please allow for breaks
and periods when the load is lower. Based on the
adjusted estimates, arrange protective measures
for the user e.g. organisational measures.
Vibration total value (vector sum of three directions)
determined in accordance with EN 62841:
a
hw
K
hw
=Voltage
= Current
=Rated input
=Power output
=No load speed
=Maximum outer diameter
=Wheel thickness
=Bore
=Max. cut diameter
( = rod, = pipe,

=Max. cut diameter
( = rod, = pipe,

=Max. vice opening
=Weight without mains cable
= Vibration emission value
= Uncertainty (vibration)
= section steel)
= section steel)