Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for ETCR 6300D
Summary of Contents for ETCR 6300D
-
Page 2: Table Of Contents
CONTENT Warning ..................... 1 I. Introduction .................... 3 II. Range and Accuracy ................4 III. Electrical Signs ................... 4 IV. Technical Specifications ..............5 V. Structure of the Leaker ............... 7 VI. LCD Display ..................8 VII. Operating Method ................8 1. -
Page 3: Warning
Warning Thank you for purchasing our company's 。 , for better use of this product, please: ——Read carefully the user's manual. ——Follow strictly safety rules and notes listed in this manual. u Under any circumstances, please pay special attention to your safety in the course of using this leaker. - Page 4 u When changing batteries, please pay attention to the polarity of battery. u Use, disassembly and maintenance of this leaker shall be operated by authorized personnel. u In case dangers would occur if continue to use a faulty leaker, please stop to use it and seal it for safekeeping immediately;...
-
Page 5: Introduction
I. Introduction ETCR6300D DC Clamp Leaker is specially designed for measurement of DC leakage current，DC low current; which resolution can reach 0.1mA, by adopting up-to-date CT technology and digital integration technology, it is a product with relatively small size, high accuracy and perfect function compared with similar leakers in the world. -
Page 6: Range And Accuracy
interface. With the help of the software that we provide, many functions are available. For example, on-line monitoring, historical data inquiry，active curve drawing. There are also functions like saving to documents and printing when connected to PC. It also has functions such as peaking holding, data holding, data storage and adjust zero. -
Page 7: Technical Specifications
be caused. Double insulation IV. Technical Specifications Measurement of DC leakage current, DC current, Function car leakage Zn-Mn dry battery,6F22,9V DC，continuous use for Power 60 hours Test Mode Clip-on CT，Magnetic modulation Clamp Size 25mm×30mm Range 0.0mA～6.00A DC Resolution 0.1mA DC 0.0mA～300.0mA DC: ±2%rdg±5dgt Accuracy （23℃±3℃，below... - Page 8 LCD Dimension 35mm×21.5mm; display domain:32mm×15mm Sampling Rate About 2 times/s Range Shift 0.0mA～6.00A DC Automatically Yes，calibrate zero before measuring Zero-Adjustment Polarity Auto identified and display“—” Indication Test Position Tested wire in the jaw center Line Voltage 600V DC Data stored in the memory of the meter via USB USB Interface upload to PC, or on-line monitoring Data Memory...
-
Page 9: Structure Of The Leaker
Limit Temperature -10℃～0℃及 40℃～50℃，within 2%rdg Error ℃ Working: -10℃～50 ,below 80%rh Temperature and Humidity Storage: -10℃～60℃,below80%rh Insulating AC3700V/rms(between the alloy of the clamp and Strength the housing) IEC1010-1、IEC1010-2-032、Pollution degree 2、 Applicable CAT Ⅲ(600V) Safety Rules V. Structure of the Leaker 1. -
Page 10: Lcd Display
VI. LCD Display 1. DC indication 2. AC indication 3. AC indication 4. Low battery symbol 5. Data hold indication 6. Stored data code 7. Unit of current indication 8. Value of current VII. Operating Method 1. Start-up, Shutdown Press key to start up, LCD will begin to display;... -
Page 11: Leaker Measurement
2. Leaker Measurement High voltage, extremely dangerous! Operators shall strictly observe safety rules; otherwise there would be risk of electric shock to cause personal injuries or casualties. Dangerous！Please don’t use it to measure current higher than 300A; otherwise there would be risk of electric shock to cause personal injuries or equipment damages. - Page 12 main line.（Note: single line） Note! In order ensure the accuracy measurement, before every measurement, close to the wire, adjust zero, and then clamp into the current line to test. 4） Read LCD display data. In case symbol was displayed, it OL mA means that current of measured line is beyond the maximum limit of this leaker;...
-
Page 13: Peak Holding
first, and then do the test. Do not test DC current exceed 7A，When the input current is more than 7A, the meter reading may become small, and does display the overrange OL symbol. 3. Peak Holding Pressing key continually in the course of measurement (More HOLD than 3 seconds), the leaker will capture current peak values of lines in this period of time;... -
Page 14: How To Change Battery
” flickering and return to measuring mode. “FULL 2）Press keys to enter into data access mode and HOLD+POWER display Unit 1 storage data automatically; and then press HOLD key again to turn the page of stored data; will display when NULL there is no data in stored in the memory, press key to exit... -
Page 15: Accessories
with qualified new battery; special attention shall be paid to the polarity of battery; at last, cover battery cover plate. IX. Accessories Clamp tester 1 pc USB Com cable 1 pc Software 1 disk User Manual 1 copy Warranty card / Certification 1 copy -13-... - Page 16 Manufactured by ETCR Electronic Technology Company Address: F-3F, No.4 Pengshang Zhifu Road, Jiahe, Baiyun District, Guangzhou, Guangdong, China Post Code: 510440 Tel: (86-20)62199556 62199554 Fax: (86-20)61100822 E-mail: info@etcr.cc Website: www.etcr.cc...
Need help?
Do you have a question about the 6300D and is the answer not in the manual?
Questions and answers