Machine Specifications; Standard Product & Accessories; Machine Set-Up - General EPIC 200 Series Operator's Manual

EPIC ® 200 SERIES ONE-MAN HOLE DIGGER
FORM GOM08042001EU, VERSION 1.0

4 MACHINE SPECIFICATIONS

FIGURE 1
ENGINE
TYPE Honda GX35
HIGH SPEED 9000 RPM (No Load)
IDLE SPEED 2900 RPM
SPARK PLUG GAP 0.762 mm (.030 inch)
FUEL Unleaded, "regular" grade gasoline (RON 87).
Consult engine manufacturer supplied
materials for specific information.
FUEL TANK CAPACITY 0.64 L (22 US ounces)
TRANSMISSION
TYPE Enclosed, spur geared, double reduction
REDUCTION RATIO 42.5 to 1
LUBRICANT
CAPACITY 224 g (8 US ounces)
LUBRICANT
SPECIFICATION High temperature transmission grease
containing an extreme pressure (EP) additive.
CLUTCH 76 mm (3 inch) diameter, automatic type
centrifugal.
MACHINE WEIGHT 13.0 Kg (28 lbs) (less auger)
AUGER CAPACITY 50.8 mm (2 inch) diameter up to and including
203.2 mm (8 inch) diameter. Refer to
DIGGING OPERATION section in this manual
for specific information.
OPERATING
ENVIRONMENTS Non-hazardous type locations.
REQUIRED NUMBER
OF OPERATORS 1
NOISE & VIBRATION EMISSIONS
Description North America
Model
Noise Level
Vibration Level
5 STANDARD PRODUCT & ACCESSORIES
Refer to FIGURE 1 for overview description of standard components included
in machine. Included in shipment for Hole Digger should be the following:
1 each, engine/transmission assembly
1 each, auger pin
1 each, bottle of engine oil
1 each, operator manual
1 each, applicable engine manual
1 each, final inspection form
Europe
242H
85 db
51 m/s²
English-EN
ACCESSORIES
NOTE: All augers, extensions, blades and screw bits are for use in general
purpose projects for a variety of soil conditions unless otherwise specified. All
auger and auger extension drive connections are 25 mm (1 inch) diameter.
Digging depth for all augers is 762 mm (30 inch) and auger extension is 381
mm (15 inch).
Part #
2350-2E
2350-3E
2350-4E
2350-6E
2350-8E
2350-15X
E244PAK3
E246PAK3
E248PAK3
P302PAK2
P801PAK3
SB26PAK3
2121PAK3

6 MACHINE SET-UP

Open shipping carton immediately upon receipt. Remove Hole Digger from
carton. Visually inspect contents of carton for freight damage and/or missing
parts. If shipping damage is evident, contact delivering carrier immediately to
arrange for an inspection of damage by their claims representative. DO NOT
DESTROY OR DISCARD SHIPPING CARTON UNTIL INSTRUCTED BY
AUTHORIZED REPRESENTATIVE OF CARRIER OR FACTORY. If missing
parts are detected, notify your dealer who will assist you in obtaining them.
ASSEMBLY
Hole Digger is hipped from factory completely assembled. The transmission is
lubricated at the factory and will not require further servicing prior to initial
usage.
1. Visually inspect throttle control, throttle control cable assembly and
carburetor for signs of damage. Rotate throttle control to determine
carburetor spring allows carburetor throttle lever to travel from its low to
high speed position and back again without any restriction and/or binding.
Throttle control level must return engine to idle speed when twist grip
throttle is released by operator.
2. Check all fasteners for security, tighten as required.
Description Cutting Weight
Diameter (in Kg)
57 mm (2.25 64 mm
inch) Auger OD (2.50 inch)
83 mm (3.25 89 mm
inch) Auger OD (3.50 inch)
102 mm) (4 5.2 inch
inch) Auger OD (133 mm)
152 mm (6 191 mm
inch) Auger OD (7.5 inch)
203mm (8 inch) 241 mm
Auger OD (9.5 inch)
No Flighting NA
Auger
Extension
102 mm NA
(4 inch) Auger
Blade
152 mm NA
(6 inch) Auger
Blade
203 mm NA
(8 inch) Auger
Blade
Auger Screw NA
Bit, 2350-3E
ONLY.
Auger Screw NA
Bit, 2350-2E
ONLY.
Auger Screw NA
Bit, all other
augers.
Auger Pin NA
3,6
4,1
5,4
6,4
8,2
1,6
0,2
0,4
0,5
0,7
1,2
1.9
0,2
3