Table of Contents
Advertisement
Quick Links
Advertisement
Table of Contents
Subscribe to Our Youtube Channel
Related Manuals for General 50-195
Summary of Contents for General 50-195
- Page 1 REVISION 2 - NOVEMBER 15/07 © Copyright General International 08/2007...
- Page 2 Because of our commit- ment to quality and customer satisfaction, General® International agrees to repair or replace, within a period of 24 months from date of purchase, any genuine part or parts which, upon examination, prove to be defective in work- manship or material.
- Page 3 To help ensure safe operation, please take a moment to learn the machine’s applications and limita- tions, as well as potential hazards. General® International disclaims any real or implied warranty and holds itself harmless for any injury that may result from improper use of its equipment.
-
Page 4: Unpacking And Setup
(Model #50-295CT). Contact your General® International distributor for more information. This manual contains instructions for both the router extension wing (Model #50-195) and the router fence (Model #50-295). Depending on your purchase, some of the information in this manual may not apply. - Page 5 In such cases the model 50-195 router table must be installed on the side opposite to the motor cover door. The unit can fit other models or brands of table saws with 27”...
- Page 6 MOUNTING A ROUTER Outer slots Inner slots Fig. 6 Fig. 7 1. Slide the T-head bolts into the T-slots allowing them 2. Adjust the rear bolts, , on the mounting clips to loosely hang from the underside of the table. until they bottom out in the slots and tilt the front Line the mounting clips up straight with the slots so edge of the clips forward.
- Page 7 TABLE INSERT RINGS The router extension wing (Model #50-195) comes with 2 remov- 1 1/8” (29 mm) 2 3/8” (60 mm) able insert rings allowing the opening on the extension wing to be changed to suit the most common sizes of router bits.
-
Page 8: Fence Adjustments
Be sure to use an appropriate size hose and fittings (not included) and check that all connections are sealed tight- ly to minimize airborne dust. If you do not already own a dust collection system, consider contacting your General® International distributor for information on our complete line of dust collection systems or visit our website at: www.general.ca... -
Page 9: Profile Cutting
JOINTING AN EDGE Jointing the edge of a board involves using a straight cutting router bit to remove wood from the edge face of a board. The result is a perfectly flat and square edge. 1. Install a straight cutting router bit into your router according to the manufacturer’s instructions. -
Page 10: Parts List
ROUTER EXTENSION WING PARTS LIST 50-195 REF. DIAG. PART N0. DESCRIPTION SPECIFICATION 50195-01 ROUTER EXTENSION WING 50195-02 TABLE INSERT 1 1/4” (29 MM) 50195-03 LOCK WASHER 50195-04 MOUNTING BOLT 7/16” X 1 3/4” 50195-05 MOUNTING CLIP 50195-06 HEX. HEAD BOLT 1/4”... - Page 11 ROUTER FENCE PARTS LIST 50-295 REF. DIAG. PART N0. DESCRIPTION SPECIFICATION 50295-01 FENCE FACE 50295-02 FENCE MOUNTING PLATE 50295-03 WASHER 50295-04 MOUNTING HANDLE 50295-05 MICRO ADJUSTMENT SLEEVE 50295-06 FENCE BODY 50295-07 THUMB SCREW 3/8” X 3/4” 50295-08 FENCE BODY BACKER PLATE 50295-09 MICRO ADJUSTMENT KNOB 50295-10...
- Page 12 50-195/295 8360, Champ-d’Eau, Montreal (Quebec) Canada H1P 1Y3 Tel.: (514) 326-1161 Fax : (514) 326-5565 Parts & Service Fax : (514) 326-5555 Order Desk orderdesk@general.ca www.general.ca IMPORTANT: When ordering replacement parts, always give the model number, serial number of the machine and part number. Also a brief description of each item and quantity...
Need help?
Do you have a question about the 50-195 and is the answer not in the manual?
Questions and answers