Jacobsen STEINER 75-70710 Owner/Operator's Manual & Illustrated Parts List

Tractor cab 420/430

Hide thumbs

Table Of Contents

Quick Links

OWNER/OPERATOR'S MANUAL

& ILLUSTRATED PARTS LIST

MODEL:

75-70710 TRACTOR CAB 420/430 CB420

WARNING: If incorrectly used this machine can cause severe injury. Those who use

and maintain this machine should be trained in its proper use, warned of its dangers

and should read the entire manual before attempting to set up, operate, adjust or

service the machine.

09-156 REV A

Table of Contents

Need help?

Do you have a question about the STEINER 75-70710 and is the answer not in the manual?

Questions and answers

Summary of Contents for Jacobsen STEINER 75-70710

Page 1 OWNER/OPERATOR’S MANUAL & ILLUSTRATED PARTS LIST MODEL: 75-70710 TRACTOR CAB 420/430 CB420 WARNING: If incorrectly used this machine can cause severe injury. Those who use and maintain this machine should be trained in its proper use, warned of its dangers and should read the entire manual before attempting to set up, operate, adjust or service the machine.
Page 2 CALIFORNIA WARNING Proposition 65 Warning The engine exhaust from this product Diesel engine exhaust and some of contains chemicals known to the State its constituents are known to the State of California to cause cancer, birth of California to cause cancer, birth defects or other reproductive harm.
Page 3: Table Of Contents
TRACTOR IMPORTANT MESSAGE Thank you for purchasing this Jacobsen product. You have purchased a world class product, one of the best designed and built anywhere. This product comes with an Owner/Operator's Manual. The useful life and good service you receive from this product depends to a large extent on how well you read and understand this manual.
Page 4: Introduction
INTRODUCTION TRACTOR DESCRIPTION The sturdy CB420 cab is carefully designed to fit the model 420 and 430 tractor equipped with a ROPS rollbar. It is extremely useful in cold weather when operating a snowblower, V-blade, or a power angle blade. Exceptional features include ease of entry from either side, full glass windshield and back window, and lightweight removable doors.
Page 5: Specifications
SPECIFICATIONS TRACTOR SPECIFICATIONS Overall Height - Installed ..................68" Overall Width ......................45" Cab Length ......................48" Head Room ......................40" Inside Roof Width ....................30" Roof Length ......................42" Roof Width (outside) ....................35"...
Page 6: Safety
Jacobsen machines. For your safety and the safety manner not specifically authorized after original of others, read and follow the information given with manufacture–including the addition of “after-market”...
Page 7 SAFETY TRACTOR GENERAL SAFETY 1. Read and understand the Owner’s Manual before attempting to operate this machine. 2. Operate all controls from the operator’s seat. NO RIDERS. 3. Keep all shields in place and safety switches adjusted properly. 4. Do not leave equipment unattended. STOP the engine and remove the key. 5.
Page 8: Assembly Instructions
ASSEMBLY INSTRUCTIONS TRACTOR 1. Have a ROPS approved roll bar and seat belt mounted to your tractor, using the roll bar instructions. NOTE: If you have a canopy on the roll bar, it needs to be removed. 2. (420 only, if applicable) Move steering cylinder mount on the treadplate to the outside hole.
Page 9 ASSEMBLY INSTRUCTIONS TRACTOR 7. Set the front panel on the tractor and insert two 5/16 X 1" bolts through the frame and treadplate. Next, bolt the top of the front panel to the front of the roof panel as shown. 8.
Page 10 ASSEMBLY INSTRUCTIONS TRACTOR 11. From the left side of the tractor, install the “S” hook on the top edge of the pump mount plate as shown in Drawing C. 12. Stretch each top elastic cord from the fabric panel across the front panel to the extended bolts.
Page 11 ASSEMBLY INSTRUCTIONS TRACTOR WWF WINDSHIELD WIPER INSTALLATION 5. Distance between stud hole and bracket hole (Except 1000 Series) should be 6.25 inches. 6. Drill tower stud hole first using a 5/8" drill. 1. Locate mounting position of wiper assembly. 2. Determine whether adequate space is 7.
Page 12: Installation
INSTALLATION TRACTOR INSTRUCTIONS FOR MOUNTING ASSEMBLED CAB ON TRACTOR 1. Tractor must be equipped with a rollbar. 2. With the cab doors removed, position the assembled cab into position around the rollbar. 3. Fasten the cab to the rollbar with the “W” clamps and 5/16 X 1 bolts. 4.
Page 13: Removal
REMOVAL TRACTOR INSTRUCTIONS FOR REMOVING ASSEMBLED CAB FROM TRACTOR 1. Disconnect wiring to wiper motor. 2. Detach the elastic cords which position the front fabric panels around the tractor. 3. Remove the doors. 4. Remove the bolts at the front corners of the tread plate and cab frame. 5.
Page 14 CAB PARTS TRACTOR FIGURE 1...
Page 15: Cab Parts
CAB PARTS TRACTOR FIGURE 1 ITEM PART NO. DESCRIPTION ITEM PART NO. DESCRIPTION 60-365.17 ROOF PANEL 1-31 57-009-99 MOULDING 44-133 HEADLINER (WINDSHIELD 99-1/4") 35-053 MOTOR-WINDSHIELD WIPR 1 1-32 56-049-10 CORD-ELASTIC 10" 35-054 WINDSHIELD WIPR ARM 45-039 HOOK-"S" 64139-04 BOLT-WLF 1/4-20X3/4 62-556 PANEL-FRONT WINDOW 1-33...
Page 16 Equipment from Jacobsen, a Textron company, is built to exacting standards ensured by ISO 9001 and ISO 14001 registration at all our manufacturing locations. A worldwide dealer network and factory-trained technicians backed by Textron Parts Xpress provide reliable, high-quality product support.

This manual is also suitable for:

Steiner cb420