Nokia RH-6 Series Disassembly Instructions Manual
Hide thumbs
Also See for RH-6 Series:
- Baseband description & troubleshooting (72 pages) ,
- Rf description & troubleshooting (74 pages)
Related Manuals for Nokia RH-6 Series
Summary of Contents for Nokia RH-6 Series
- Page 1 Customer Care Solutions RH-6 Series Cellular Phones 5 - Disassembly Instructions Copyright © 2003 Nokia Corporation. Issue 1 10/2003 Page 1 Company Confidential...
- Page 2 Remove vibra Motor ........................ Remove microphone ........................ Remove DC-jack ........................Remove release Spring ......................Remove SIM flIp ........................Move flip from A-cover ......................Exchange of battery connector X103.................. Copyright © 2003 Nokia Corporation Page 2 Issue 1 10/2003 Company Confidential...
- Page 3 3 Remove the battery from the B-Cover. 4 Unscrew the two T6 screws, in the order shown. For assembly, they should be replaced in the reverse order to a torque load of 21Ncm. Copyright © 2003 Nokia Corporation. Issue 1 10/2003 Page 3...
- Page 4 7 Remove the A-cover as shown. 8 Unscrew five T6 screws, in the order shown. For assembly the reverse order should be used with a torque load of 25Ncm. Copyright © 2003 Nokia Corporation Page 4 Issue 1 10/2003 Company Confidential...
- Page 5 10 Carefully unplug the display connector by removing the UI-shield from the PWB. 11 Carefully separate the UI-shield from the PWB. 12 Remove speaker, when assembling, note the location of the guide pin. Copyright © 2003 Nokia Corporation. Issue 1 10/2003 Page 5...
- Page 6 B-cover you first have to expand the B-cover, then pull up the shielding. 15 To remove colour frame from antenna, use SRT-6 tool to unlock the snap. 16 Remove the Power key. Copyright © 2003 Nokia Corporation Page 6 Issue 1 10/2003...
- Page 7 19 Use tweezers to pull up the microphone. 20 To remove the DC-jack, place tweezers between the spring contacts and under the jack. You will need to use additional force to pull the jack upwards. Copyright © 2003 Nokia Corporation. Issue 1 10/2003 Page 7...
- Page 8 22 Expand the B-cover carefully and remove the SIM-Flip. 23 Insert keyboard flip disassembly tool pin SS-6 into the flip cover hole. 24 Push the pin down to the end and move toward the right. Copyright © 2003 Nokia Corporation Page 8 Issue 1 10/2003...
- Page 9 26 Move whole flip cover off from A-cover. (take care when handling the FLEX) Exchange of battery connector X103 1 Indicated are the two soldered support angles. 2 Using a side cutter, cut the two support angles. Copyright © 2003 Nokia Corporation. Issue 1 10/2003 Page 9 Company Confidential...
- Page 10 4 Desolder all pins and clean the pads. 5 Note: a soldering iron with a higher temperature is required, when cleaning or soldering the ground pad. 6 Note location markings to fit the connector precisely. Copyright © 2003 Nokia Corporation Page 10 Issue 1 10/2003 Company Confidential...
- Page 11 7 Tin one of the pads to fix the connector before soldering the following pins. 8 Place connector between the markings and solder first support angle. If position is exact, solder remaining pins. Copyright © 2003 Nokia Corporation. Issue 1 10/2003 Page 11...
- Page 12 RH-6 Company Confidential 5 - Disassembly Instructions CCS Technical Documentation [This page intentionally blank] Copyright © 2003 Nokia Corporation. Page 12 Issue 1 10/2003 Company Confidential...