C o n t e n t I. Safety Instructions .................... 2 II. Functions and Technical Specification ............. 3 III. Features and Identification of Parts............... 3 Operation and Settings .................. 4 V. Multiple Protection Functions ................8 Handling and Transportation ................. 9 VII.
Safety Instructions 1. This machine uses the standard voltage: 115V/60Hz。If you have any questions regarding to the following instructions, please contact a qualified electrician. 2. The unit must be installed in accordance with national wiring regulations. Check available power supply and resolve any wiring problems before installation and operation of this unit - voltage standard: 115V/60Hz.
Cautions ※ Keep the unit at least 1 meter away from TV or radios to avoid electromagnetic interference. ※ Do not expose the unit under direct sun light to avoid surface color fading. ※ Do not tilt the unit for more than 35 degrees or upside-down while transporting. ※...
2. Identification of Parts: Top panel Protective net Front shell 10. Drain hole Horizontal louvers 11. Side filter Universal wheel 12. Remote control Chassis 13. Exhaust hose Back shell 14. Exhaust hose adapter Back filter 15. Drain cover connector Universal plug fixing holes 16.
Page 6
2. Control panel list: On/Off button Up button Mode button Timer button Down button Fan speed button Fan speed Timer indicator Water-full indicator indicator Dehumidify mode Fan mode Cool mode indicator indicator Sleep mode Fahrenheit temperature Power indicator indicator indicator LED display Celsius temperature Timer indicator...
Page 7
) and fan speed can be adjusted to Room temperature can be set within a range of 17-30℃(62-86 ℉ high or low level. On/Off time can be set. E1, E2 & E4 protection (see Troubleshooting). Water-full warning protection. 2.
Page 8
Only final setting is effective if repeated setting. The time can be adjusted within a range of 1-24 hours, press “Up” or “Down” button to increase or decrease 1 hour. Unit will not change working mode after timer setting. Timer will not stop by other functions. ...
1. Press and glide the battery cover on the back of the remote control, then you can remove the cover. 2. Insert two new alkaline AAA batteries into the battery compartment. Be sure to note the proper polarity. 3. Reattach the battery cover and make sure the locking tab clicks into place. Be sure to note proper polarity of batteries Notes:...
Handling and Transportation 1. Handle and move the unit Hold the top of the air outlet window in front panel with one hand and the handle at the top of back panel with another hand, then move the unit in upright position (As shown in Photo below). Note: ...
Page 11
If window seal-plate will be in vertical position, and will be at left side of window, the slant panel A of adapter should be at right direction. If window seal-plate will be in vertical position, and will be at right side of window, the slant panel A of adapter should be at left direction.
Page 12
1.4 Installation of the unit Move the unit together with its exhaust hose assembly in front of the window and keep the unit at least 50cm away from the walls or other objects. (As Photo). Install the rectangle end of exhaust hose adapter into the corresponding rectangle hole in window seal-plate assembly, fix it with screw and close the window (as Photo).
Important notes: The exhaust hose is 280mm-1500mm long and which is determined by the specification of the air-conditioner (s). Do not use prolonged the hose or replace it with other different hoses as this may affect the functions of the air-conditioner. The exhaust hose must be smooth or it may lead air-conditioner overheat and trip because exhaust hose is obstructed.
Drain hose must be installed before unit starts working. When unit is operating in cooling mode, to ensure enough water to recycle in the unit to cool condenser and enhance cooling performance, so it is not suggested to use continuous drainage ...
2.2 Installation of the filter Special note: Be sure to install the filters to side panel at first then the filter into back panel. Aim the end of the filter toward slot then push filter in even force gently into slot. Notes: Install the filter with opposite direction of removal.
Troubleshooting Please check the unit and suggestions below before asking for professional service, but never dismantle or repair the unit by yourself, it may cause harm to you and your property. Trouble Cause Remedy Connect the unit to a live socket and Power supply failure turn it on.
XII. Appendix Fuse parameters Model: FSD or 50F Voltage: 250V Current: 3.15A Schematic diagram of the air conditioner Capillary Condenser Compressor Evaporator For specific technical parameters of the model, refer to rating label on the product. Correct Disposal of this product This marking indicates that the product should not be disposed with other household wastes throughout the world.
Page 18
February 24, 2019 Great products so far. Fast delivery, easy setup, and working without any issues. With your inspiring rating, COSTWAY will be more consistent to offer you EASY SHOPPING EXPERIENCE, GOOD PRODUCTS and EFFICIENT SERVICE! US office: Fontana, California...
Need help?
Do you have a question about the EP24041 and is the answer not in the manual?
Questions and answers
Costway FP10518US error code E2. What I've done: 1. turn off disconnect for 5 minutes. 2. clean filter. 3. check drain. All good. What do you suggest?