Launch X-PROG 3 User Manual
  1. Manuals
  2. Brands
  3. Launch Manuals
  4. Car Alarm
  5. X-PROG 3
  6. User manual

Launch X-PROG 3 User Manual

Hide thumbs Also See for X-PROG 3:
Table of Contents

Advertisement

Quick Links

LAUNCH
Copyright
Copyright © 2021 by LAUNCH TECH CO., LTD. All rights reserved. No part of
this publication may be reproduced, stored, or transmitted in any form without
the written permission of the copyright owner.
Trademark
Launch is a registered trademark of LAUNCH TECH CO., LTD in China and
other countries. All other marks are trademarks or registered trademarks of
their respective owners.
Disclaimer
The contents of this document are subject to changes without notice due to
continued improvements in design, manufacture, and methodologies. Launch
is not liable for the damage or losses due to the use of this document.
FCC Statement
Any Changes or modifications not expressly approved by the party responsible
for compliance could void the user's authority to operate the equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions:
a. This device may not cause harmful interference
b. This device must accept any interference received, including interference
that may cause undesired operation.
Note: This equipment has been tested and found to comply with the limits for
a Class B digital device, pursuant to part 15 of the FCC Rules. These limits
are designed to provide reasonable protection against harmful interference
in a residential installation. This equipment generates uses and can radiate
radio frequency energy and, if not installed and used in accordance with
the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular
installation. If this equipment does cause harmful interference to radio or
television reception, which can be determined by turning the equipment off
and on, the user is encouraged to try to correct the interference by one or
more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
X-PROG 3 User Manual
I

Advertisement

Table of Contents
loading

Related Manuals for Launch X-PROG 3

Summary of Contents for Launch X-PROG 3

  • Page 1 LAUNCH X-PROG 3 User Manual Copyright Copyright © 2021 by LAUNCH TECH CO., LTD. All rights reserved. No part of this publication may be reproduced, stored, or transmitted in any form without the written permission of the copyright owner. Trademark Launch is a registered trademark of LAUNCH TECH CO., LTD in China and...
  • Page 2 LAUNCH X-PROG 3 User Manual - Consult the dealer or an experienced radio/TV technician for help. The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction. Important: Please read this manual carefully and understand the safety precautions before performing any operation to this product.
  • Page 3 LAUNCH X-PROG 3 User Manual • Do not attempt to replace the internal rechargeable lithium battery. Contact the dealer for factory replacement. • Use the included battery and charger. Risk of explosion if the battery is replaced with an incorrect type.
  • Page 4 LAUNCH X-PROG 3 User Manual • MCU cable with multiple leads • EEPROM converter • User Manual...

  • Page 5: Table Of Contents

    Table of Contents 1 About this Manual ...................1 1.1 Target Reader ..................1 1.2 Typographic Conventions ..............1 1.3 Symbols ....................1 2 About X-PROG 3 ....................2 2.1 Product Overview ................2 2.2 Power Source ..................3 2.3 Technical specifications ...............4 2.4 Accessories ..................4 3 Diagnostics .....................4...

  • Page 6: About This Manual

    1 About this Manual This manual introduces the basic information of X-PROG 3 and instruction on the product usage. X-PROG 3 is a powerful anti-theft solution and an ideal choice for professional repair shops and vehicle maintenance businesses. It has achieved vehicle key, Engine and gearbox programming, featuring powerful multiple parts reprogramming and wide range of vehicle coverage.

  • Page 7: About X-Prog 3

    LAUNCH X-PROG 3 User Manual 2 About X-PROG 3 2.1 Product Overview...

  • Page 8: Technical Specifications

    LAUNCH X-PROG 3 User Manual Part Name Description To connect with all anti-theft DB26 diagnostic connector cables. Benz key slot To place Benz car key. To place car key for RF Key slot defection. Key chip slot To place key chip.

  • Page 9: Accessories

    LAUNCH X-PROG 3 User Manual 2.3 Power Source The product does not have an independent power supply, you can power it up via either of the followings ways: • Use the included power adaptor • Connect the device through the vehicle’s DLC 2.4 Accessories...
  • Page 10 LAUNCH X-PROG 3 User Manual Connect the programmer and the engine to read engine or BENCH mode gearbox ECU (Connect engine cable ECU with the BENCH mode cable based on BENCH mode diagram). Connect the programmer MCU Converter with MCU(chip soldering is required in this procedure).
  • Page 11 LAUNCH X-PROG 3 User Manual MCU cable with To connect the programmer multiple leads and MCU.

  • Page 12: Diagnostics

    X-PROG 3 User Manual 3 Diagnostics X-PROG 3 diagnostic function supports key programming, engine and gearbox replacement for various of vehicles, you can retrieve ECU information, read, erase, and write in for a range of chips as shown in the product options.

  • Page 13: Establish Wireless Connection

    1. Slide down the status bar from the top. , go to Wireless and network -> Bluetooth. 2. Touch 3. Select the X-PROG 3 to be connected, wait until the connection is successful. • 3.1.3 Perform Common Operations You should enter the function interface before using the programmer.

  • Page 14: Diagnostic Operations

    LAUNCH X-PROG 3 User Manual 4. Depending on your requirement, touch any of the following options : • Gearbox Learning • Anti-Theft System • Engine System 3.2 Diagnostic Operations • 3.2.1 Key Programming You can use anti-theft system to access key chip programming functions. The product supports reading, retrieving and writing key information, as well as other key-related functions.
  • Page 15 You can use key programming function to backup old key data and write in data for new keys. Below procedure shows you how to perform key programming for BMW using Launch diagnostic product, it contains backup current key data and new key generation.
  • Page 16 LAUNCH X-PROG 3 User Manual c. Touch Key Operation. d. Touch Key Learning. e. Touch OK after reading the the onscreen instruction.
  • Page 17 LAUNCH X-PROG 3 User Manual f. Touch OK. g. Touch OK to save the key data. h. Enter the key file name and touch OK. i. Key file saved, touch OK to confirm.
  • Page 18 LAUNCH X-PROG 3 User Manual 2. Generate a new key. a. Touch the desired blank key position. b. Place the new key into the programmer key slot and touch OK. c. Confirm the key type, if the you are using a smart key, touch YES.

  • Page 19: Gearbox Programming

    • Operating on gearbox programming Below procedure shows you how to perform gearbox programming for a BMW using Launch diagnostic product, the procedure contains gearbox connection and erasure of gearbox data.
  • Page 20 LAUNCH X-PROG 3 User Manual 1. Connecting the gearbox. a. On the programmer function interface, touch EGS System to enter gearbox programming. b. Touch the correct chassis type. c. You will then see a corresponding connection diagram. Touch OK.
  • Page 21 LAUNCH X-PROG 3 User Manual 2. Erasing gearbox data. a. Touch EGS Erasure. b. Touch DOWNLOAD. c. Touch OK.
  • Page 22 LAUNCH X-PROG 3 User Manual d. Touch DOWNLOAD. e. Touch OK. f. Touch YES. g. Touch YES.

  • Page 23: Engine Programming

    • Operating on Engine Programming Below procedure shows you how to perform engine programming for a Volkswagen using Launch diagnostic product, the procedure contains chip ID...
  • Page 24 LAUNCH X-PROG 3 User Manual retrieval, engine connection, data backup and data restoration. 1. Retrieve chip ID. a. Touch Engine. b. Select Engine Brand. c. Touch Search for ECU model.
  • Page 25 LAUNCH X-PROG 3 User Manual d. Check ECU model (printed on the sticker on the back of your Engine), enter the engine type in the dialogue box(In example below,the engine type should be MED17.7.7). e. Touch OK.
  • Page 26 LAUNCH X-PROG 3 User Manual 2. Connect the engine. a. Touch View Wiring Diagram. b. Read the connection diagram, perform the proper connection based on the engine type and then touch OK. c. Touch Read chip ID.
  • Page 27 LAUNCH X-PROG 3 User Manual d. When below dialogue box appears, touch OK. 3. Backup data. a. Touch Backup EEPROM Data. b. Enter the file name for EEPROM data.
  • Page 28 LAUNCH X-PROG 3 User Manual c. Confirm the storage path, and touch OK. d. Touch OK. e. Follow the onscreen instructions to backup flash data also when the above is done. 4. Restore EEPROM data. Stop: The EEPROM restoration applies only when you have encountered irrevocable faults.
  • Page 29 LAUNCH X-PROG 3 User Manual b. Touch Backup EEPROM file name. c. Confirm the selected Backup EEPROM file, and touch OK. d. When the data is successfully restored, touch OK.
  • Page 30 LAUNCH X-PROG 3 User Manual...

  • Page 31: Software Upgrade

    LAUNCH X-PROG 3 User Manual 4. Software Upgrade The software update function keeps your diagnostic software & App up-to- date, you can also use it to customize your frequently used software. To update Diagnostic Software & APP: 1. On the main diagnostic screen, tap Software Update to enter the update center.
  • Page 32 LAUNCH X-PROG 3 User Manual Note: • You may stop the process by tapping Stop, and tap Continue to resume the process later. • In case of network connection failure, tap Retry. 3. You will see below dialogue box once the installation is completed.

  • Page 33: Warranty

    LAUNCH automotive meters, except as stated herein. The exclusive remedy for all automotive meters found to be defective is to repair or replace, and LAUNCH has no liability for any consequential or incidental damages. The following cases are not covered in product warranty: •...

Table of Contents