Depth Gauge; Dust Collection System - Makita HR3011FC Instruction Manual

Depth gauge

The depth gauge is convenient for drilling holes of uniform depth.
Press and hold the lock button, and then insert the
depth gauge into the hex hole. Make sure that the
toothed side of the depth gauge faces the marking.
► Fig.16: 1. Depth gauge 2. Lock button 3. Marking
4. Toothed side
Adjust the depth gauge by moving it back and forth
while pressing the lock button. After the adjustment,
release the lock button to lock the depth gauge.
NOTE: Make sure that the depth gauge does not
touch the main body of the tool when attaching it.
Dust cup
Optional accessory
Use the dust cup to prevent dust from falling over the
tool and on yourself when performing overhead drilling
operations. Attach the dust cup to the bit as shown in
the figure. The size of bits which the dust cup can be
attached to is as follows.
Model
Dust cup 5
Dust cup 9
► Fig.17: 1. Dust cup
Dust cup set
Optional accessory
For Models HR3011FC, HR3001C
NOTICE:
When using the dust cup set in
HR3011FC, HR3001C, the spacer is also requied.
Before installing the dust cup set, remove the bit from
the tool if installed.
Attach the spacer to the dust cup set.
dust cup is aligned with the groove in the spacer.
► Fig.18: 1. Spacer 2.
Install the dust cup set with the spacer on the tool so
that the symbol on the dust cup is aligned with the
groove in the tool.
► Fig.19: 1. symbol 2. Groove
To remove the dust cup set, remove the bit while pulling
the chuck cover in the direction of the arrow.
► Fig.20: 1. Bit 2. Chuck cover
Hold the spacer and pull it out.
► Fig.21
For Model HR3012FC
Before installing the dust cup set, remove the bit from
the tool if installed.
Install the dust cup set on the tool so that the
bol on the dust cup is aligned with the groove in the tool.
► Fig.22: 1. symbol 2. Groove
To remove the dust cup set, remove the bit while pulling
the chuck cover in the direction of the arrow.
► Fig.23: 1. Bit 2. Chuck cover
Bit diameter
6 mm - 14.5 mm
12 mm - 16 mm
symbol on the
symbol 3. Groove
sym-
Hold the root of dust cup and pull it out.
► Fig.24
NOTE: If you connect a vacuum cleaner to the dust
cup set, remove the dust cap before connecting it.
► Fig.25: 1. Dust cap
NOTE: If the cap comes off from the dust cup, attach
it with its printed side facing up so that groove on the
cap fits in the inside periphery of the attachment.
► Fig.26
Tool hanger
Optional accessory
WARNING:
and screw.
WARNING:
tool hanger only.
WARNING:
check for damages, cracks or deformations, and
make sure that the screw is tightened.
CAUTION:
Install or remove the tool hanger
on a stable table or surface.
The tool hanger is intended for connecting the lanyard
(tether strap). To install the tool hanger to the tool,
follow the steps below.
1. Disconnect the plug from the power source.
2. Insert the projections of the tool hanger into the
holes on the tool.
3. Tighten the screws firmly.
► Fig.27: 1. Tool hanger 2. Hole 3. Projection
4. Screw
DUST COLLECTION
SYSTEM
For HR3011FC, HR3012FC only
Optional accessory
The dust collection system is designed to collect dusts
effectively when the concrete drilling operation.
► Fig.28: 1. Dust collection system
CAUTION:
Make sure that the tool is switched
off and unplugged before carrying out any work
on the tool. Failure to do so may result in personal
injury from accidental start-up.
CAUTION:
Always attach the filter to the
dust collection system. Failure to do so cause dust
inhalation.
CAUTION:
Check that the filter is not dam-
aged. Failure to do so may cause dust inhalation.
13 ENGLISH
Do not use damaged tool hanger
Use the screw provided with the
Before using the tool hanger,