Maintenance; Cleaning The Hepa Filter - Makita DVC265 Instruction Manual

State of abnormality
T h e c leaner d oes not run along w ith
th e sw itc h operation of th e tool.
T h e c leaner runs w h ile th e tool' s
sw itc h trigger is not pulled .
C annot erase all tool registrations in
th e c leaner.

MAINTENANCE

CAUTION:
Always be sure that the tool is
switched off and the battery cartridge is removed
before attempting to perform inspection or
maintenance.
NOTICE:
Never use gasoline, benzine, thinner,
alcohol or the like. Discoloration, deformation or
cracks may result.
T o maintain pro d u c t S A F E T Y an d R E L I A B I L I T Y ,
repairs, any other maintenance or adjustment should
be per f orme d b y Makita A ut h ori z e d or F a c tor y S er v i c e
C enters, al w a y s using Makita repla c ement parts.
Probable cause (malfunction)
T h e w ireless unit is not installed into th e
c leaner and / or th e tool.
T h e w ireless unit is improperly installed
into th e c leaner and / or th e tool.
T h e terminal of th e w ireless unit and / or
th e slot is d irty .
T h e w ireless ac tiv ation button on th e
tool h av e not been push ed .
T h e stand -by sw itc h on th e c leaner is
not set to " I ( O N) " .
More th an 1 0 tools are registered to
th e c leaner.
T h e c leaner erased all tool
registrations.
No pow er supply
T h e tool and c leaner are aw ay f rom
eac h oth er ( out of th e transmission
range) .
R ad io d isturbanc e by oth er applianc es
w h ic h generate h igh -intensity rad io
w av es.
O th er users are using th e w ireless ac ti-
v ation of th e c leaner w ith th eir tools.
P ressing th e w ireless button on th e tool. P ress th e w ireless button on th e c leaner f or erasing
T h e stand -by sw itc h on th e c leaner is
not set to " I ( O N) " .
T h e w ireless ac tiv ation button is not
h eld d ow n c orrec tly .
19 ENGLISH
Remedy
I nstall th e w ireless unit c orrec tly .
G ently w ipe of f d ust and d irt on th e terminal of th e
w ireless unit and c lean th e slot of th e c leaner and /
or th e tool.
P ush th e w ireless ac tiv ation button on th e tool
briefly. Make sure that the wireless activation lamp
is blinking in blue.
S et th e stand -by sw itc h on th e c leaner to " I ( O N) " .
P erf orm th e tool registration again.
I f more th an 1 0 tools are registered to th e c leaner,
th e tool registered earliest w ill be c anc elled
automatic ally .
P erf orm th e tool registration again.
S upply th e pow er to th e tool and th e c leaner.
G et th e tool and th e c leaner c loser to eac h oth er.
T h e max imum transmission d istanc e is approx i-
mately 1 0 m h ow ev er it may v ary ac c ord ing to th e
c irc umstanc es.
Keep th e tool and th e c leaner aw ay f rom th e appli-
anc es suc h as W i-F i d ev ic es and mic row av e ov ens.
P erf orm one of th e f ollow ing w ay ;
- set th e stand -by sw itc h on th e c leaner to " O "
position or;
- turn of f th e w ireless ac tiv ation button of th e oth er
tools or;
- c anc el th e tool registration of th e oth er tools.
all tool registrations.
S et th e stand -by sw itc h on th e c leaner to " I ( O N) " .
H old d ow n th e w ireless ac tiv ation button f or more
th an 6 sec ond s and th en release it w h en th e w ire-
less ac tiv ation lamp blinks in red . H old d ow n th e
w ireless ac tiv ation button f or more th an 6 sec ond s
again until th e w ireless ac tiv ation button rapid ly
blinks in red and th en release th e button.

Cleaning the HEPA filter

CAUTION:
Do not use the vacuum cleaner
without a filter or continue to use dirty or dam-
aged filter. Vacuumed dust or particles may be
exhausted from the cleaner and they may cause
respiratory disease to the operator.
NOTICE:
To keep optimum suction power and
clean exhaust, clean the filter periodically. If
enough suction power is not obtained even after
the cleaning, replace the filter with new one.
To prevent the filter from being dam-
NOTICE:
aged, do not use following tools and similar items
for cleaning :
— Air duster
— High pressure washer
— Tools made of hard materials such as a
metallic brush