Husqvarna Automower 405X Operator's Manual page 24

2. Use the arrow buttons and the OK button to move
through the menu structure
Security level .
3. Use the arrow buttons and the OK button to select
the level of security.
4. Push the OK button.
3.10.5.2 To create a New loop signal
The loop signal is randomly selected to create a unique
link between the product and the charging station. In
rare cases, there may be a need to generate a new
signal, for instance if two adjacent installations have a
very similar signal.
1. Place the product in the charging station.
To get access to the menu on
2. Do steps 1–3 in
page 22 .
3. Use the arrow buttons and the OK button to move
through the menu structure
New loop signal .
4. Await confirmation that the loop signal has been
generated. This normally takes about 10 seconds.
3.10.5.3 To change the PIN-code
To get access to the menu on
1. Do steps 1–3 in
page 22 .
2. Use the arrow buttons and the OK button to move
through the menu structure
Advanced > Change PIN-code .
3. Enter the new PIN code.
4. Push the OK button.
5. Enter the new PIN code again.
6. Push the OK button.
7. Make a note of the new PIN code. Refer to
Introduction on page 3 .
3.10.5.4 To change the duration of the alarm
1. Do steps 1–3 in To get access to the menu on
page 22 .
2. Use the arrow buttons and the OK button to move
through the menu structure
Duration > Duration of alarm .
3. Use the arrow buttons to select a time interval of 1
to 20 minutes.
4. Push the BACK button.
3.10.6 Messages
In this menu the previous fault and information
messages can be found. For some of the messages,
there are tips and advice to help to rectify the fault.
Troubleshooting on page 36 .
Refer to
24 - Installation
If the product is disrupted in any way, for example it is
Settings > Security > trapped or the battery is low, a message is saved
relating to the disruption and the time it happened.
If the same message is repeated several times, this may
indicate that an adjustment to the installation or the
product is required. Refer to
3.10.6.1 To read the messages
1.
2.
3.
3.10.7 Weather timer
Security > Advanced >
Weather timer automatically adjust the cutting time to
the growth of the grass. The product is not permitted to
operate more than the schedule settings.
Note:
Settings > Security >
to make as much operating time as possible available
for
than necessary.
The first operation of the day is set by the schedule
settings. The product always complete 1 mowing cycle,
and then
continue to operate or not.
Note:
operate for more than 50 hours, or if a
settings is done. Weather timer is not changed if a Reset
of schedule settings is done.
Security > Advanced >
3.10.7.1 To set the Weather timer
1.
2.
3.
4.
3.10.7.2 To set the Weather timer frequency
Set how frequently the product cuts the grass when the
Weather timer is in use. There are 3 frequency levels:
Low, Mid and High . The higher the frequency, the more
sensitive the product is to the grass growth. That is, if
Installation on page 14 .
To get access to the menu on
Do steps 1–3 in
page 22 .
Use the arrow buttons and the OK button to move
through the menu structure
messages and Messages > Info messages .
Read the messages and read the
to get information and recommendations to correct
the faults.
Weather timer , it is recommended
When using
Weather timer . Do not restrict the schedule more
Weather timer selects if the product will
Weather timer is reset if the product does not
To get access to the menu on
Do steps 1–3 in
page 22 .
Use the arrow buttons and the OK button to move
through the menu structure
Weather timer .
Push the OK button to select the
Push the BACK button.
Messages > Fault
Troubleshooting
Reset of all user
Weather timer > Use
Weather timer .
1650 - 003 - 24.02.2021