Electrical Connection; Intended Use - DeWalt DW714 Instruction Manual

ENGlIsH
TO REDUCE THE RISK OF INJURY, ALLOW SAW TO
RETURN TO THE FULL UP POSITION
AFTER EACH OPERATION. THINK! YOU CAN
PREVENT ACCIDENTS.

Electrical Connection

Be sure your power supply agrees with the nameplate
marking. 120 volts, AC means that your saw will operate on
alternating current only. A voltage decrease of 10 percent
or more will cause a loss of power and overheating. All
D WALT tools are factory tested. If this tool does not
e
operate, check the power supply.
Accessories

WARNING: Since accessories, other than those
offered by D WALT, have not been tested with this
e
product, use of such accessories with this tool could be
hazardous. To reduce the risk of injury, only D
recommended accessories should be used with
this product.
Recommended accessories for use with your tool are
available for purchase from your local dealer or authorized
service center.
saw Blades:
ALWAYS USE 10" (254 mm) SAW BLADES WITH 30 mm
(NoTE: Some regions are 25.4 mm) ARBOR HOLES. SPEED
RATING MUST BE AT LEAST 4600 RPM. Never use a smaller
diameter blade. It will not be guarded properly. Use crosscut
blades only! Do not use blades designed for ripping,
combination blades or blades with hook angles in excess of
7 degrees.
BLADE DESCRIPTIONS
APPLICATION
Construction Saw Blades (thin kerf with anti-stick rim)
General Purpose
Fine Crosscuts
Woodworking Saw Blades (provide smooth, clean cuts)
Fine crosscuts
Non-ferrous metals
Aluminum Cutting Saw Blades (provide smooth, clean cuts)
Fine crosscuts
NOTE: For cutting non-ferrous metals, use only saw blades with TCG
teeth designed for this purpose.
NOTE: More teeth will get better cutting surface quality.
COMPONENTS (FIG. A, C, D, L)

WARNING: Never modify the power tool or any part
of it. Damage or personal injury could result.
Refer to Figure A at the beginning of this manual for a
complete list of components.

INTENDED USE

Your D WALT DW714 Miter Saw has been designed for
e
professional cutting wood and aluminum, wood products,
aluminum products and plastics. It performs the sawing
operations of cross-cutting, bevelling and mitering easily,
accurately and safely.
48
WALT,
e
DIAMETER TEETH
10" (254 mm) 40
10" (254 mm) 60
10" (254 mm) 80
10" (254 mm) 80
10" (254 mm) 80/100/120
This unit is designed for use with a nominal blade diameter
10" (254 mm) carbide tip blade.
Do NoT use under wet conditions or in presence of
flammable liquids or gases.
These miter saws are professional power tools. Do NoT
let children come into contact with the tool. Supervision is
required when inexperienced operators use this tool.
ASSEMBLY

WARNING: To reduce the risk of serious personal
injury, turn off the tool and disconnect it from
the power source before attempting to move it,
change accessories or make any adjustments. An
accidental start-up can cause injury.
Unpacking Your Saw (Fig. A, C, D1, E1, E2)
Check the contents of your miter saw carton to make
sure that you have received all parts. In addition to this
instruction manual, the carton should contain:
1 DW714 miter saw with blade.
1 Saw blade
1 Dust bag
32
1 Vertical clamp
33
2 Work supports 35
1 Blade wrench 9
Fig. C
32
33
1. Remove the saw from the packing material carefully
using the carrying handle (
saw on a smooth, flat surface such as a workbench or
strong table.
Fig. D1
2. Use the supplied blade wrench
lock temporary shipping bolt
35
13 , Fig. D1). Place the
13
to remove the miter
9
(Fig. D2).
34