Die Set User Manual - ACCO Brands GBC StreamPunch Ultra Operation & Instruction Manual

8. DIE SET USER MANUAL

The die sets for the StreamPunch Ultra are intended to work with
multiple paper sizes and sheet feed directions. In order to
accommodate different sheet sizes this die set must be configured to
the correct number of punching pins and the die stop must be set to
the proper position. The die label contains information on the common
paper punching sizes, for the uncommon sizes please refer to Table 1.
Glossary
LEF- Long Edge Feed- Indicates that the paper is being fed through
the machine so that the longer side of the sheet will be punched.
SEF- Short Edge Feed- Indicates that the paper is being fed through
the machine so that the shorter side of the sheet will be punched.
Statement (STMT) Paper- 8.5" X 5.5"
Legal Paper- 8.5" X 14"
Ledger Paper- 11" X 17"
Pin Numbering
Die punching pins are numbered sequentially starting from the handle
end. Figure 8.1 shows a 47 hole coil die (404757) as an example. All
square and round hole die sets follow the same pin numbering format.
Pin #47
Figure 8.1 Coil Die Set Pin Numbering
Figure 8.2 Pressure Bar Removal
Pin Removal
Wire
Coil
2:1
Rnd/Oval
Rnd/Sq
US Paper Sizes
Ricoh Part Number 404757 404758
404771 404768
LTR LEF 2, 47 1, 23
LTR SEF 7, 42 NONE
STATEMENT LEF 7, 42 NONE
LEGAL SEF 7, 42 NONE
LEDGER SEF 2, 47 1, 23
9" x 12" LEF 1, 2, 47 1, 23
9" x 12" SEF 6, 7, 42, 43 3, 21
12" x 18" SEF 1, 2, 47 1, 23
Wire
Coil
2:1
Rnd/Oval
Rnd/Sq
ISO Paper Sizes
Ricoh Part Number 404757 404758
404771 404768
A4 LEF NONE NONE
A4 SEF 7, 41 4, 21
A5 LEF 7, 41 4, 21
A3 SEF NONE NONE
SRA4 LEF NONE NONE
SRA4 SEF 6, 7, 41, 42 4, 21
SRA3 SEF NONE NONE
*For CombBind 20H configuration pull Pin Number 1
The above chart shows the information on which pins need to be removed to correctly punch each sheet size and configuration that the StreamPunch
Ultra can accept. For standard offering dies not found in the chart no pin adjustment is necessary.
Pin #1
Quarter Turn
Fastener
Wire 3/5/7
3 Hole
3:1 Hole
8mm
Rnd/Sq 8mm
Pin numbers to be removed based on paper size and orientation
404759 404760 404762
404769
1, 34 NONE 3H/5H/7H
5, 31 N/A N/A
5, 31 N/A N/A
5, 31 N/A N/A
1, 34 NONE 3H/5H/7H
1, 34 NONE 3H/5H/7H
5, 31 N/A N/A
1, 34 NONE 3H/5H/7H
Wire 3/5/7
3 Hole
3:1 Hole
8mm
Rnd/Sq 8mm
Pin numbers to be removed based on paper size and orientation
404759 404760 404762
404769
NONE N/A N/A
5, 30 N/A N/A
5, 30 N/A N/A
NONE N/A N/A
NONE N/A N/A
4, 5, 30, 31 N/A N/A
NONE N/A N/A
Table 8.1 Pin Removal Guide
StreamPunch
To remove punch pins from the StreamPunch Ultra first turn the two
Quarter Turn Fasteners counter clockwise to release the pressure bar.
Remove the pressure bar and set aside.
Lift up and remove the desired pins according to Table 8.1. Store pins
in the pin storage tray inside front door of machine making sure pins
cannot be dropped, damaged or lost while removed.
Replace the pressure bar by lining up dowel pin holes with exposed
dowel pins. Hold pressure bar so that it is seats completely over dowel
pins and then rotate Quarter Turn Fasteners clockwise until a click is
felt to lock pressure bar in position.
Important! Make sure pressure bar is attached and both Quarter Turn
Fasteners are in the locked position prior to inserting the die set into
the machine or serious damage can occur to both the machine and die
set.
2/4 2/4 2/4
Hole Hole Hole
8mm 6.5mm SCAN
404763 404763 404764
N/A N/A N/A
N/A N/A N/A
N/A N/A N/A
N/A N/A N/A
N/A N/A N/A
N/A N/A N/A
N/A N/A N/A
N/A N/A N/A
2/4 2/4 2/4
Hole Hole Hole
8mm 6.5mm SCAN
404763 404763 404764
2H/4H 2H/4H NONE
1, 4 1, 4 NONE
1, 4 1, 4 NONE
2H/4H 2H/4H NONE
2H/4H 2H/4H NONE
1, 4 1, 4 NONE
2H/4H 2H/4H NONE
Ultra/Ultra MP
TM
Figure 8.3 Pressure Bar
Figure 8.3 Pin Removal
Dowel Pin Holes
Figure 8.4 Replace Pressure Bar
VeloBind VeloBind
11 Hole 12 Hole CombBind
LTR A4
404765 404766 404768
NONE N/A 1, 21
N/A N/A NONE
N/A N/A NONE
N/A N/A NONE
NONE N/A 1, 21
NONE N/A 1, 21
N/A N/A 3, 19
NONE N/A 1, 21
VeloBind VeloBind
11 Hole 12 Hole CombBind
LTR A4
404765 404766 404768
N/A NONE NONE
N/A N/A 4, 19
N/A N/A 4,19
N/A NONE NONE
N/A NONE NONE
N/A N/A 4, 19
N/A NONE NONE
GB
eWire
Rnd/Sq
404770
404772
1, 34
N/A
5, 31
5, 31
1, 34
1, 34
5, 31
1, 34
eWire
Rnd/Sq
404770
404772
NONE
5, 30
5, 30
NONE
NONE
4, 5, 30, 31
NONE
10